Felisatti T770 Instructions De Service page 16

INDEX
INTRODUCTION
1. GENERAL INFORMATION
2. TECHNICAL CHARACTERISTICS
3. GENERAL SAFETY STANDARDS
4. INSTALLATION
5. REGULATION
6. OPERATION AND USE
7. MAINTENANCE
8. PROBLEMS - CAUSES - REMEDIES
9. PART REPLACEMENT
INTRODUCTION
You have purchased a mitre saw from the new Felisatti
range, a high quality product superbly designed to
complete your set of tools.
This series of mitre saws is the perfection of the already
established Felisatti equipment range.
Should there be any malfunctions you can always count
on the customer service network which is now at your
complete disposal.
All FELISATTI portable tools conform EN 61029, CE 98/37
machine directives and following modifications and, with
regard to electromagnetic compatibility, the tools conform
with directive EEC 89/336, and EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3.
The mark on the tool guarantees its
conformity.
If used with the care and serviced regularly, this tool will
provide long-lasting and reliable service.
Carefully follow the instructions contained in this manual,
using them for reference for any eventual controls that may
need to be carried out.
1 GENERAL INFORMATION
1.0 THE AIM OF THIS MANUAL
This manual has been compiled by the manufacturer and
is an integrative part of the tool equipment.
The information contained is for the benefit of
professional operators.
This manual defines the aims for which the tool has been
constructed and contains all the necessary information to
guarantee correct and safe use.
It is therefore strongly recommended that this manual
is consulted before performing any kind of adjustment
operation, use or maintenance tasks.
Constant observance of the standard regulations
contained in this manual will guarantee both machine and
operator safety, economic working and longer functional
operation of the tool itself.
Photographs and drawings have been supplied by the
constructor for exemplifying purposes.
All manuals and user guides at all-guides.com
INSTRUCTIONS FOR
MITRE SAW
With the aim of following a policy of constant development
page 9 and product modernization, the constructor is entitled to
» 9 make modifications without forewarning.
» 9
1.2
» 11
Plate A (fig. 1) identifies the mitre saw model. Plate B
» 11
contains mitre saw model references, engine technical
» 11
data and information about its manufacturer.
» 12
1.2.1 IDENTIFICATION
» 14
A Logotype plate
» 15
B Data plate
» 15
C Switch push-button
D Unlock push-button of safety hook
E Switch lock push-button
F Upper surface support
G Upper surface
H Blade unit
I
K Turntable
L Base
M Support
1.2. CONSTRUCTOR:
FELISATTI elettroutensili S.p.A.
Via del Lavoro n.16/18 44100 Ferrara - Italy
Tel. +39 0532 595111 - Fax +39 0532 595199
E-mail: info@felisatti.com
Web site: www.felisatti.com
A sturdy structure and high reliability make these mitre
saws suitable for industrial wood, aluminum and steel
cutting (only T777CE and T778CE), retaining standard
handling qualities without compromising ease of
transport.
Models T770, T777, T 777 CE are equipped with a wide
upper surface, that allows the machine to be used as
a circular saw, for cutting (up to 45 mm thickness),
engraving, butting and trimming.
Models T770, T777, T777 CE are equipped with double
working surfaces (lower and upper) and a release switch
with hold button.
Models T771,T778,T778CE are supplied without an upper
surface and equipped with the release switch.
Models T777CE, T778CE are equipped with a new
electronic unit for slow blade starting and stopping in
about 5 seconds; it provides constant motor speed (r.p.m.)
independently of the pressure exerted on the blade
during operation. Speed can however be varied manually
according to the cutting material.
Only one operator should use the mitre saw. Design and
construction conform to IEC 1029.1 and EN 60204.1
standards.
9
MITRE SAW IDENTIFICATION
Blade
2 TECHNICAL CHARACTERISTICS