Analog Operation - Hornby Hobbies Jouef Waterman Serie Mode D'emploi

FEATURES:
• Factory preset address for the locomotive is 03.
• 40 khz frequency for a smoother motor control.
• The V.4 decoder supports DCC, Motorola, DC, AC and Marklin
• 14, 28 or 128 selectable speed steps for DCC systems.
• Load compensation function.
• Outputs overload protection for all functions.
• Audio amplifi er 2W 4 Ohms.
DECODER PARAMETERS ADJUSTING:
The V.4 Loksound decoder (32 Mbit) controls several parameters. You can fi nd a list of the most important
ones at the end of this instructions. Each parameter (CV) can be confi gured independently using its respective command.
DCC Systems (Lenz, Intellibox, etc.)
It is much easier to modify the parameters if you have a DCC compatible digital system or an Intellibox. Please, read the corresponding chapter in your system manual (DCC decoders
programming). The V.4 Loksound decoder support any NMRA programming system.

ANALOG OPERATION

When using conventional transformer, the locomotive movement will be similar to that of a locomotive without a decoder. The locomotive will only start its running when receiving a minimum
voltage between 5.5 and 6 volts, as the decoder will not work with a lower tension. Please note the following warnings: The decoder installed in your Rivarossi locomotive has been specifi cally
adapted for this model and it should be used only in this particular model. Always disconnect the decoder from the power supply before doing any work on it.
If removing the speaker were necessary for maintenance purposes, please handle it very carefully.
Do not put any pressure on it or touch the speaker membrane.
The reset function is very convenient, as you can set the original factory values again at any time. You can use this function with DCC and Motorola systems. To use this function, type "8" in CV 8
or "08" in register "08".
Adjust the sound volume.
The lokSound allows the individual volume control of each sound. Please refer to the following table to see which CV you need to change:
KEY FUNCTION
F0 Light on/off
F1 Sound on/off,
F2 Whistle long
F3 Short whistle
F4 Rear light red (Aux 1& 2)
F5 Cab light (Aux 3 & 4)
F6 Shunting illumination
F7 Compressor
F8 Rail clank
F9 Conductor´s signal
Before you change any of the volume control CVs, please make sure that the CV 31 is set to 16 and CV 32 = 1! These two CVs are used as index selection registers to distinguish between the real function of
CV 257-511.
The master volume control CV 63 controls all sound effects. The resulting sound volume for each individual sound effect therefore is a mixture of the master volume control settings and the individual volume control sliders.
CV NAME DESCRIPTION
1 Loco address. Locomotive address
2 Start voltage. Sets the minimum speed of the engine
3 Acceleration. This value multiplied by 0.869 is the time from stop to maximum speed.
4 Deceleration. This value multiplied by 0.869 is the time from maximum speed to stop.
5 Maximum speed. Maximum speed of engine
6 Medium speed. Averall engine speed
8 Manufacturer's ID. Manufacturer's ID (ESU). Set CV8 to value 8 for automatic resetting.
13 Analogue mode F1-F8. Status of functions F1 to F8 in analogue mode.
Bit
0
1
2
3
4
5
6
7
17 Extended address Extended engine addresslng address of engine
18 Extended address Extended engine addresslng address of engine
®
digital systems.
SOUNDSLOTS VOLUME CVs VALUE
1, 24 259, 443 128, 128
16 379
15 371
5 291
7, 8 307, 315 128, 128
6 299
Function
F1
F2
F3
F4
F5
F6
F7
F8
Locomotive 2D2 5500 Waterman
Programming track
KEY FUNCTION
F10 Sanding valve
F11 Coupler clank
128 F12 Station announcement #1
128 F13 Station announcement #2
F14 Compressed air lef off
F15 Pantograph up/down
F16 Switch fl ange
128 F17 curve squeal
Ramdon sounds
100 Brake sounds
When programming using Lenz, Uhlenbrock
or Arnold equipment, please refer to their
programing instructions. If the error message
"err02" is displayed during programming
with Lenz or Arnold equipment, a 47
Resistance 47
Ohmresistor (0.5) Watt or higher) must be
inserted between one of the two supply
Central unit
cables and the programming track.
SOUNDSLOTS VOLUME CVs
11
4
13
14
12
9
22
10
RANGER
1 - 255
1 - 255
1 - 255
1 - 255
1 - 255
1 - 255
0 - 255
Value
1
2
4
8
16
32
64
128
Service Sheet HJBD-21
April 2015 - Subject to technical modifi cations
VALUE
339 128
283 128
355 128
363 128
347 70
323 128
427 128
331 128
451 128
459 128
VALUE
3
1
43
35
200
68
151
25
192
128