air&me CLEVAIR 2 Guide D'utilisation page 9

MAIN FUNCTIONS
HYGROSMART FUNCTION: HygroSmart
®
D
This mode allows you to maintain an ideal humidity level in the air (between 47% and 53%).
Once the function has been selected, a warning light is displayed (
By selecting this function, the unit turns on as soon as the humidity level of the room is below
47%, stops once the ideal range is reached and restarts as soon as the humidity level drops
again. If there is enough moisture in your room, the unit will not work.
ELECTRONIC HYGROSTAT FUNCTION: By selecting this function, you can set the humidity level
E
of the surrounding air to the desired value (between 30 and 75%).
1. Press the electronic hygrostat button (
2. Set the desired humidity level by pressing the button several times (the increase is done in
increments of 5%).
3. After 3 seconds, the digital display will show the ambient humidity again. A indicator light
appears ( ). The unit will start automatically until the desired humidity level is reached
g
and then stop automatically.
The unit can be set to CONTINUOUS, which is ideal if you want to humidify a room quickly.
To activate this function, press the Electronic Hygrostat button several times until "CO" is dis-
played. After 3 seconds, the digital display will show the ambient humidity again.
NEGATIVE IONISATION FUNCTION: This function allows you, thanks to the diffusion of negative
F
ions, to clean the air and to give you a sensation of well-being both biological and physiologi-
cal. Once the function is selected, a light is displayed (
MIST POWER: Clevair 2 has 3 speeds (Low - Medium - High:
G
dification of the air and to adjust the intensity of the mist. The humidification speed can only
be adjusted when the HygroSmart
the Electronic Hygrostat function or the Automatic mode.
At full power, the mist produced may form condensation around the unit and give the im-
pression of a leak in the tank. To avoid this phenomenon, reduce the power of diffusion and/
or place the humidifier towards a source of heat (about 1 meter).
WARM MIST MODE: By selecting this function, the device will broadcast a haze preheated
H
between 35 and 40 ° C. The diffusion of warm vapor will allow a humidification better distri-
buted in the room thanks to a soft and healthy mist.
Once the desired settings are enabled, press the warm steam button (
indicate the triggering of this function (
To avoid the risk of burns, the appliance alternates between 30 minutes of heating and 10
minutes of cold steam.
After having chosen the desired function, without any action on your part, the screen of the
device automatically goes to "standby".
16
is an exclusive technology patented by air&me.
®
).
f
).
E
).
c
) to increase the speed of humi-
a
mode is activated. This function is not compatible with
®
). The indicator will
H
).
e
ZUSÄTZLICHE FUNKTIONEN
AROMATHERAPY: Clevair 2 has an aromatherapy function. To use it, press the broadcast drawer
at the bottom of the left side of the device (
(4 to 8 drops depending on the desired olfactory power) of the essential oil of your choice on
the cotton. Close the drawer and turn on the unit. It is recommended to renew the cotton with
each change of essential oil.
Never put essential oils directly in the water tank: this will damage the unit.
LED LIGHT : You can easily turn off the LED light of your humidifier. To do so, press the
for 5 seconds. If you wish to turn on the LED light, press the
MAINTENANCE
• Make sure the unit is turned off and unplugged before handling.
• Do not immerse the device in water or any other liquid.
• Do not use corrosive, abrasive or flammable products to clean the unit.
CLEANING THE TANK: To avoid scale deposits, clean the tank at least once a month with a
suitable product or white vinegar. To do this, remove the tank from the unit and remove the
cap, then fill it with water and cleaning agent. Let stand for 15 minutes, then empty and rinse
the tank thoroughly with clean water before putting it back in place and turning on the device
again.
CLEANING ULTRASONIC PLATE : Dry the ultrasonic plate and clean it with a soft brush. Then wipe
it with a soft cloth.
STOCKAGE: To avoid any bacteria or virus proliferation, never store the appliance with water
inside the tank and be sure that the appliance is perfectly dry.
1. Empty and clean the tank.
2. Clean the pre-filter.
3. Store the product in a place that is protected against dust and that is clean and dry.
). Once the drawer is open, pour a few drops
14
F
button again for 5 seconds.
F
button
17