Niko 350-20066 Manuel page 8

350-20066
6. TROUBLESHOOTING
Problem Cause
The lighting is not switched on. Incorrect wiring.
The ambient light level is too
high.
The lighting is not switched off. The switch-off delay is too long.
Detector has false triggering.
Incorrect wiring.
The red LED does not turn on. PIR is not selected as the
detection method.
The movement is outside the
detection range of the PIR sensor.
A cover cap is used so that there
is no detection on the place of the
movement.
The green LED does not turn on. US is not selected as the
detection method.
The movement is outside the
detection range of the ultrasonic
sensor.
False triggering The following elements may
affect the proper functioning of
the ultrasonic sensor and may
cause false triggering:
- air flows
- sound absorbing materials,
carpet, curtains, ...
- heat sources
- reflective objects
- objects subject to wind
- wiring (a reverse wiring between
N and L will cause reduced
sensitivity of the ultrasonic
sensor sensitivity and will limit
the detection area)
7. TECHNICAL DATA
dimensions
power supply voltage
power consumption
detection angle
mounting height
detection range
protection degree
protection class
ambient temperature
quality mark
nv Niko sa
Action
Refer to the wiring diagram and
check if the lighting is working.
Check the set lux value and
adjust if necessary (higher value).
Check the switch-off delay and
adjust if necessary (lower value).
Check for any objects in the room
that may cause false triggering
and remove them from the
detection area.
Check the wiring diagram.
Select PIR as the detection
method.
The movement should be within
the detection range (8 m).
Remove or reposition the cover
cap.
Select US as the detection
method.
The movement should be within
the detection range (10 x 16 m).
- Activate the potentiometer for
light sensitivity (ON). This will
reduce the sensitivity of the
ultrasonic sensor by ± 10 to
40%, depending on the severity
of the air flow.
- Avoid aiming the detector
toward any heat sources, such
as air conditioning, electric fans,
heaters or reflective surfaces.
- Make sure there are no objects
within the detection range that
are subject to wind.
- Check the wiring diagram.
60 x 120 mm (HxW)
230 Vac ± 10%, 50 Hz
1 W
360°
2 – 3 m
US: 10 x 16 m (138 m²)
PIR: ø 8 m (50 m²)
IP20
class I devices
0 – 45°C
CE marked in compliance with EN 60669-2-1
Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu
8. WARNINGS REGARDING INSTALLATION
• The installation should be carried out by a registered installer and in compliance with the statutory regulations.
• This user manual should be presented to the user. It should be included in the electrical installation file,
and it should be passed on to any new owners. Additional copies are available on the Niko website or via
the Niko support service.
• During installation, the following should be taken into account (non-exhaustive list):
- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this user manual, which only states general regulations and should therefore be read within the scope
of each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EU declaration of conformity regarding this product at www.niko.eu.
9. NIKO SUPPORT
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can
be found at www.niko.eu under the "Help and advice" section.
10. GUARANTEE PROVISIONS
• The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of
purchase of the product by the consumer. If there is no invoice, the date of production applies.
• The consumer is obliged to inform Niko in writing about the non-conformity, within two months after
stating the defect.
• In case of a non-conformity, the consumer only has the right to a product repair or replacement free of
charge, which shall be decided by Niko.
• Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
• The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
Do not dump this product with the unsorted waste. Bring it to a recognised waste collection point. Together with producers
and importers, you have an important role to play in the advancement of sorting, recycling and reusing discarded electrical
and electronic appliances. In order to finance the waste collection and processing, the government levies a recycling
contribution in some cases (included in the purchase price of this product).
PM350-20066R16362