Publicité
Liens rapides
CONTENTS
• CONTENU • CONTENIDO
500 lb (227 Kg) on-road
300 lb (136 Kg) off-road
800 lb (363 Kg) Static Load Limit
AVAILABLE ACCESSORIES
SideBar Short Bed
#8001153
Load Stop
#8001161
Pour le français, aller à la page 5.
Instruction #1036089B-1/7
base pad (4X)
locking pin (2X)
plaque de base (x 4)
goupille de verrouillage (x 2)
placa de base (4X)
pasador de bloqueo (2X)
plate (4X)
plaque (x 4)
placa (4X)
LOAD CAPACITY
• CAPACITÉ • CAPACIDAD DE CARGA
227 kg (500 lb) sur route
136 kg (300 lb) hors route
charge statique : limite de
363 kg (800 lb)
• ACCESSOIRES DISPONIBLES • ACCESORIOS DISPONIBLES
SideBar Long Bed
#8001154
Eye Bolts
Rotopax Mounting Kit*
#8001162
M8 acorn nut (6X)
écrou borgne M8 (x 6)
tuerca ciega M8 (6X)
M13/19mm wrench (1X)
clé M13/19 mm (x 1)
llave M13/19 mm (1X)
fuera de la carretera: 300 lb (136 kg),
sin movimiento: 800 lb (363 kg)
HD Hook Straps
#8001165
#8001167
Para español ir a la página 5.
Bed Track Kit 2
M8x35 t-bolt (8X)
boulon en T M8 x 35 (x 8)
perno para ranura en T M8x35 (8X)
M8 flat washer (8X)
rondelle plate M8 (x 8)
arandela plana M8 (8X)
T15 Torx wrench (1X)
clé Torx T15 (x 1)
llave Torx T15 (1X)
en carretera: 500 lb (227 kg),
Ladder Roller
#8001163
*Rotopax mount sold separately
*Le support Rotopax se vend à part.
*El montaje Rotopax se vende por separado.
Publicité
Manuels Connexes pour Yakima Bed Track Kit 2
Sommaire des Matières pour Yakima Bed Track Kit 2
- Page 1 Bed Track Kit 2 CONTENTS • CONTENU • CONTENIDO base pad (4X) locking pin (2X) M8x35 t-bolt (8X) plaque de base (x 4) goupille de verrouillage (x 2) boulon en T M8 x 35 (x 8) placa de base (4X)
- Page 2 ASSEMBLE THE T-BOLTS INSERT THE T-BOLT/PLATE ASSEMBLIES. WITH THE PLATES. Clean your HD Tracks, then Insert 2 t-bolt through insert 2 assemblies into the track each plate as shown. on each side of your vehicle. POSITION THE ASSEMBLIES. Move the assemblies to the approximate position where you’ll install your OverHaul HD™...
- Page 3 The Bed Track 2 base pad is trimmable. In some cases installation won’t be possible without trimming the pads. In other situations the installation will be more aesthetically pleasing if the pads have been trimmed. In the following step, place the base pads and tower then determine if trimming is necessary or desired.
- Page 4 POSITION THE BASES. Equally measure from the cab to the base of the towers to position your front rack. Then equally measure from the front towers to position the rear towers. NOTE: Minimum crossbar spread is 36” (91.4 cm) to make use of the full load capacity.
- Page 5 OverHaul HD™ o OutPost HD™. Il est possible d’adapter les plaques de base en les taillant. Las placas de base Bed Track Kit 2 se pueden recortar. En Dans certains cas, l’installation ne sera pas possible sans tail- ciertos casos la instalación no será...
- Page 6 Afin de pouvoir remplacer des clés perdues ou défectueuses, prendre note du In order to replace any lost or defective keys, note the lock and key numéro de la serrure et des clés ci-dessous et les enregistrer à www.yakima. numbers below and register them at www.yakima.com.
- Page 7 Usted debe respetar al pie de la letra estas instrucciones de uso y utilizar solamente las piezas de origen provistas. Para reemplazar una llave perdida o defectuosa, anote más abajo los números de la cerradura y de la llave y regístrelos en www.yakima.com. Instruction #1036089B-7/7...