Warranty; Accessories And Spare Parts . En; Transport; Storage - Kärcher AT Mode D'emploi

1 Pressure reducer
2 Manometer
ER1 Unstable pressure measurement due to defective valve con-
nector or hose.
ER2 Unstable pressure measurement due to defective valve con-
ER7 nector or hose.
Tyre pressure is too low.
ER3 Tyre pressure is too low.
ER4 Tyre pressure is too high.
ER5 Voltage supply is interrupted.
ER6 Failure in the electronics
ER8
ER9
ERU
ERB
ERP The valve connector comes loose during inflation.
Tyre pressure is not stable.

Warranty

The warranty terms published by our com-
petent sales company are applicable in
each country. We will repair potential fail-
ures of your accessory within the warranty
period free of charge, provided that such
failure is caused by faulty material or de-
fects in fabrication. In the event of a warran-
ty claim please contact your dealer or the
nearest authorized Customer Service cent-
er. Please submit the proof of purchase.
Accessories and Spare Parts
Only use original accessories and spare
parts, they ensure the safe and trouble-free
operation of the device.
For information about accessories and
spare parts, please visit www.kaerch-
er.com.

Transport

CAUTION
Risk of injury and damage! Observe the
weight of the appliance when you transport
it.
 When transporting in vehicles, secure
the appliance according to the guide-
lines from slipping and tipping over.

Storage

CAUTION
Risk of injury and damage! Note the weight
of the appliance in case of storage.
8
Faults with display
EU Declaration of Conformity
We hereby declare that the machine de-
scribed below complies with the relevant
basic safety and health requirements of the
EU Directives, both in its basic design and
construction as well as in the version put
into circulation by us. This declaration shall
cease to be valid if the machine is modified
without our prior approval.
Product: AT, AT Fp
AWT, AWT Fp
PT, PT Fp
MA 80, MA 80-3
Type: 1.534-xxx
Relevant EU Directives
2006/42/EC (+2009/127/EC)
2014/30/EU
2014/35/EU
Documentation supervisor:
MTM Hydro Srl
Via Moglia, 33
12062 Cherasco (Cn) - Italy
Tel. +39 0172 427311
Fax +39 0172 495437
C.F./R.I./P.IVA/V.A.T.: IT 02469390047
Cap. Soc. € 255.000 - REA CN-178422
CCIAA
info@mtmhydro.it
PEC: mtmhydro@multipec.it
3
-
EN
Replace the valve connector or the hose.
Replace the valve connector or the hose.
Check the pressure on the pressure gauge and readjust the
pressure reducer if necessary.
Check the pressure on the pressure gauge and readjust the
pressure reducer if necessary.
Inform Customer Service.
Check that the valve connector is seated correctly.
Check the pressure on the pressure gauge and readjust the
pressure reducer if necessary.
www.mtmhydro.it
2016/11/01

Technical specifications

Electrical connection
Voltage
Frequency
Power Input
Type of protection
Compressed air
Flow rate
Pressure
Working conditions
Temperature with frost
protection
Temperature without
frost protection
Humidity
Noise emission
Sound pressure level L
Sound power level L
Uncertainty K
Dimensions
Length
Width
Height
Weight
V 230
Ph/Hz 1/50
W 450
IPX4
l/min 100
MPa 0,1...0,8
°C -10...+40
°C +5...+40
% 10...80
dB(A) <70
pA
dB(A) 76,8
WA,
dB(A) 4
WA
mm 423
mm 423
mm 1550
kg 55