WOLFF 73888 Mode D'emploi Original page 16

Functional description
Please refer to the graphics on pages 2 - 4 while
you read the operating instructions.
Restriction of use
The ROBO-STRIPPER is designed exclusively for cutting
grooves in screed without the use of water and
in combination with a Dust Category M vacuum cleaner..
When the machine is used in another way, it shall be
regarded as unfi t for the purpose. Uzin Utz AG shall not
accept any liability for damage resulting from non-intended
use.
Declaration of Conformity
We declare under our sole responsibility that this product is
in conformity with the following standards of standardization
documents: DIN EN 1037, EN ISO 12100, DIN EN 60204-1,
DIN EN 60745-1, DIN EN 55014-1, DIN EN 55014-2,
according to the provisions of the: 2006/42/EC,
2004/108/EC, 2006/95/EC.
Dipl.-Ing. (FH) Dieter Hammel
Authorised to issue this declaration and for the gathering
of the technical documentation.
2017/01/04 i.V.
Uzin Utz Tools GmbH & Co.KG | 74360 Ilsfeld | Ungerhalde 1
Technical data
Power supply .................................................230 V AC
Frequency ............................................................50 Hz
Power consumption drive ............................ 2 x 900 W
Power consumption impact............................. 1.300 W
Stroke rate .........................................3.000 stroke/min.
Weight total...................................................ca. 276 kg
Additional weight front.....................................4 x 21 kg
Additional weight back .........................................25 kg
Blade's width. ...................................................350 mm
Speed ....................................................0 - 18,8 m/min.
Speed rverse .........................................0 - 25,1 m/min.
Includes:
1 ROBO-STRIPPER1
1 Blade 350x60x5 mm
1 U-shape blade, top cutting edge
1 U-shape blade, bottom cutting edge
1 Blade cover
1 Tool pouch
1 Hearing protection
2 Torsion locking device
1 Two hand grease gun
1 Grease cartridge WHS 2202
1 Protecting gloves
1 Fork wrench SW24
1 Clue Star-shaped knob
1 Allen key SW 6
1 Ring fork wrench SW17
1 Manual
1 Spare parts list
Safety Warnings
2.1 General Power Tool Safety Warnings
Read all safety warnings and all
Warning
instructions.
Failure to follow the warnings and instructions may
result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmosphe
res, such as in the presence of fl ammable
liquids, gases or dust.
Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools.
Unmodifi ed plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges and
moving parts.
EN
16