AEG BSS 4812 Mode D'emploi page 26

Chaîne hi-fi avec bluetooth
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 13
English
26
1 x USB connection cable (USB A / B)
1 x stereo cinch cable
Connections and general information
Power supply
• Make sure the mains voltage of your wall socket corre-
sponds to the voltage on the rating plate of the appli-
ance.
• Make sure the POWER switch is set to "0".
• Connect the mains cable to jack 8 of the right speaker
box.
• Connect the mains plug to a properly installed isolated
ground receptacle.
Connecting left and right speaker boxes
• The appliance is delivered with a 5-meter long connec-
tion cable.
• Use this cable to connect the jacks 9 and 10 of the speak-
ers.
NOTE: Pay attention to the shapes of the plugs!
Connecting audio and data sources
Would you like to connect your Bluetooth sound system to a
PC or an audio system?
For doing so, please use one of the connection cables
included in the delivery scope.
NOTE:
• When connecting the cables, please observe the user
instructions of your PC or audio system.
• When powering the Bluetooth sound system via USB
connection with a PC, please follow the on-screen
instructions.
• In case the plugs do not fit your external devices, you
may purchase appropriate adapter cables available in
specialty department stores.
Installation location
For maximum sound entertainment, consider the following
when installing your Bluetooth sound system.
• Choose a stable, level, and anti-slip surface.
• The speakers should be located at face level.
• Place the speakers at an angle of 60° each from the main
seating position.
Operation
Switching the appliance on
• Use the POWER button to switch on the appliance. The
VOLUME / INPUT control on the front will light up red,
indicating that the appliance is in standby mode.
NOTE:
After approx. 25 minutes without any signal input, the appli-
ance will automatically switch into standby mode. Press the
VOLUME / INPUT control to use the appliance again.
Selecting a sound source
The VOLUME / INPUT control can be used to set the desired
volume level and furthermore to select a function mode.
• Press the VOLUME / INPUT control; changing colors
indicate the following modes:
Purple/blue
= AUX
Blue
= Bluetooth
Green
= USB
Orange/green = TRS
• Press and hold the VOLUME control for 2 seconds to
switch into standby mode (red).
Volume
Turn the VOLUME / INPUT control to set the desired volume
level.
Sound
• In AUX, TRS, and Bluetooth modes, please set the vol-
ume at the source device to a suitable level.
• Use the settings of slide switch 6 to emphasize (+2db) or
muffle (-4db) high-pitched tones.
Information on the wireless Bluetooth connection
Bluetooth involves a technology for wireless radio connec-
tion of devices over a short distance. Devices with Bluetooth
standard are transmitting between 2.402 and 2.480 GHz in
the ISM band (Industrial, Scientific and Medical). Interference
can be caused for example by WLAN-networks, DAB radios,
cordless phones, or microwave ovens which work on the
same frequency band.
This device offers you the possibility to use a Bluetooth-
enabled device. The functional radius is limited to approx. 15
metres depending on the surroundings and the unit used.
If your playing device supports the A2DP profile (Advanced
Audio Distribution Profile) and has a music-player function,
then you can also wirelessly transfer music to the device. The
A2DP profile involves a multi-vendor Bluetooth profile. By
streaming, stereo-audio signals are wirelessly transferred be-
tween the playing device (source) and the receiving device.
Due to the different device manufacturers, models, and
software versions, a full functionality cannot be guaranteed.
• Logging on devices (Pairing)
Before you listen to music via the unit, you must pair the
devices.
1. Ensure, that the Bluetooth function is activated in
your player (e.g. mobile phone). For this, refer to the
operation manual of your player.

Publicité

Table des Matières
loading

Table des Matières