Dri-Eaz Ace TurboDryer Instructions page 3

3. Set the switch at the desired speed. Setting I is for low speed
and setting II is for high speed.
4. Check for proper operation before leaving the unit unattend-
ed. Do not move or carry the TurboDryer when it is running.
ELECTRICAL CONNECTIONS
Ace TurboDryers are designed to operate on a 115V/60 Hz elec-
trical connection. Make sure that the electrical outlet is grounded
and that all safety precautions are taken.
MAINTENANCE
Always turn off the power before performing maintenance proce-
dures. All the service procedures below are to be executed with
the unit unplugged. Perform before each use or as needed.
INSPECT ELECTRICAL SYSTEM: Inspect the electrical cord for
damage at regular intervals. Periodically, remove the housing
and inspect internal wiring for bare wires, insecure fasteners,
and discoloration. Remove and repair any damaged wiring as
needed. Failure to do so may lead to electrical shock or a fire
hazard.
CLEAN GRILLS: Clean off any accumulated lint or other materi-
als from the protective grill cover. A buildup will reduce the air-
flow and may cause the motor to overheat and become a fire
hazard.
CLEAN EXTERIOR: Clean the housing with mild detergent and
water. Bring back the original shine with a vinyl cleaner and
polish like those used on automobile plastics.
EXTERIOR INSPECTION: Evaluate exterior components and
make sure they are properly installed. Listen to the unit for ab-
normal sounds. Repair or replace components as needed.
TROUBLESHOOTING
In COLUMN 3, the technician in the field can handle "FS" or Field Solutions. Others solutions should be handled by a repair technician – an "AST"
or Authorized Service Technician.
WARNING: Execute all the service procedures below only with power turned off, i.e., unplugged.
PROBLEM
Motor won't run
Motor runs but blade turns
erratically or scrapes
Unit vibrates excessively
FOR PARTS AND SERVICE CALL YOUR LOCAL DISTRIBUTOR, or the Dri-Eaz Service Department at 800-932-3030.
07-01475F F259-115V
CAUSE
No power to machine
Switch not turned on
Fan blade jammed
Intake or exhaust grill blocked
Switch is broken
Loose wiring
Severe jolt has caused motor mount to
bend and fan blade to rub
Accumulation of soil on fan blade
Fan blade has lost balance
Fan blade has been bent
Bent motor shaft
Periodic Maintenance (as needed)
Make sure unit is unplugged and the blade has stopped. Re-
move four screws to remove each grill cover. This will permit
access to motor and fan blade for cleaning.
CLEAN COMPONENTS: Use compressed air or a vacuum to
remove lint and dust from fan blade, motor and grill covers.
DO NOT WET MOTOR OR WIRING: To prevent damage to
electrical components, do not use a hose or pressure washer to
clean a TurboDryer. If electrical components do become wet, dry
them immediately.
MOTOR BEARINGS: The bearings on all Dri-Eaz
TurboDryers are permanently lubricated. Do not oil.
SPECIFICATIONS
Operating positions
Amperage
Power
Air movement
RPM
Static pressure
Motor rating
Motor speeds
Thermal protection
Switch
Fan blade
Dimensions
(H × D × W)
Use weight
Ship weight
Stackable
Handle
Cord length
Safety
Specifications are subject to change without notice. Some
values are approximate.
See
above SOLUTION
FS Plug in the unit; check circuit breaker or fuse
FS Turn on the switch
FS Remove material jamming balde
FS Turn machine off and allow to cool, then remove blockage
AST Call distributor or Dri-Eaz for replacement switch
AST Check wiring and tighten as needed
AST Remove motor from housing, then replace or repair bent motor
mount
FS Clean fan blade
AST Balance or replace fan blade
AST Replace fan blade
AST Replace motor
3
6
1.5A
115V / 60Hz
1,954 CFM | 3320 CMH
1670 low 1756 high
0.6 in. | 1.5 cm
¼ hp TEAO
2-speed PSC
Thermal cut-off
2-speed rocker
16.5 in. | 41.9 cm axial
24 × 20.3 × 19 in.
61 × 51.5 × 48.3 cm
33 lbs. | 15 kg
38 lbs. | 17 kg
Yes
Molded
25 ft. | 7.6 m
UL/cUL listed
Dri-Eaz Products, Inc.