IHP UZY5 Instructions D'installation

INSTALLATION INSTRUCTIONS FOR INSTALLING A BLOWER KIT
FOR USE WITH WOOD-BURNING FIREPLACES LISTED IN TABLE 1
KIT CONTENTS
2 ea. Blower Assembly
1 ea. Instruction Sheet
TOOLS NEEDED
Robertson (square) or Phillips (star) screwdriver
Blower Kits
Cat. No. Model
UZY5/PUZY5 Blower Kit - Brentwood™ SP, BIS
Villa Vista™, WCT4820WS, WCT6820WS, WRT4826WH,
UZY5 UZY5 BIS Panorama™, Montecito™ and BIS Tradition CE™,
Montecito Estate™, WCT6840WS, Montecito Estate CAT,
WCT6940WS and BIS Tradition™
Table 1
GENERAL INFORMATION
These blower kits can easily be installed when the fireplace has a pre-
installed junction box. You just have to plug them in.
If you encounter any problems, need clarification of these instructions or
are not qualified to properly install this kit, contact your local distributor
or dealer.
Read this instruction sheet in its entirety before beginning the installation.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO
THESE INSTRUCTIONS.
SHUT DOWN THE APPLIANCE AND ALLOW IT TO COMPLETELY COOL
BEFORE PROCEEDING.
The blowers have magnetic blower mounts. The junction box (factory
installed on approved fireplaces for the use of this blower kit) must be
connected to 120 VAC service before permanently enclosing the fireplace.
Blower
with Magnet
Figure 1
IHP reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for
fireplace code information.
Printed in U.S.A. © 2000 Innovative Hearth Products
P/N F49 Rev. H 02/2017
Description
Ultima-1,
®
Blower
with Magnet
Rating: 120 volt, 60HZ , .63A
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
P/N F49
Rev. H, 02/2017
The blower must be plugged directly into a properly grounded
three-prong receptacle, 120 VAC, 60 Hz, single phase. Do not
cut or remove the grounding prong from this plug.
Installation must be in accordance with National Electrical
Code, ANSI/NFPA 70 - latest edition. In Canada, the current
CSA C22.1 Canadian Electrical Code - latest edition.
The access hole for connecting the 120 VAC is located on the lower back
right exterior side of the fireplace.
CAUTION: Should this blower kit require servicing, the power supply
must be disconnected.
These blowers do not need regular maintenance however, periodic cleaning
is required. Check the area under the firebox and in front of the blowers
and wipe or vacuum at least once a month during the operating season.
INSTALLATION INSTRUCTIONS
Step 1. Open the bottom louver of the fireplace or remove the front facade,
as appropriate.
Step 2. If replacing an existing kit, remove the old kit first. In some units
this may require the removal of the Catalytic Bypass Gauge (pull it
up and out of bracket) and mounting screws.
Step 3. Install the blowers into the center back of the unit.
Step 4. For units with a pre-existing thermodisc fan switch, the switch in
the kit may be discarded, and the connectors attached to the exist-
ing switch. For all others, install the thermodisc magnetic mount
assembly under the firebox towards the right side.
Step 5. If equipped with a Catalytic Bypass Gauge, reinstall it.
Thermodisc, Automatic
Thermal Fan Activator
Connector for
Optional Rheostat
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
HEARTH PRODUCTS
KITS AND ACCESSORIES
BLOWER KITS
UZY5 / PUZY5
WARNING
Electrical Connection
with Ground Connection
IHP
1