Good Earth Lighting AC1068-WHG-12LF0-G Mode D'emploi

Hardware kit* / Trousse de quincaillerie*/ Kit de aditamentos*
12VDC 12VDC
LED tape light
Ruban lumineux à DEL
Luz LED con cinta autoadhesiva
Power cord
Cordon d'alimentation
Cable de alimentación
DO NOT ATTEMPT TO INSTALL TAPE LIGHT WHILE PLUGGED IN.
This product has a polarized plug (one blade is wider than the other) to reduce the risk of electric shock. The plug only fits one way into a polarized outlet. DO NOT ALTER THE PLUG.
READ THE ENTIRE MANUAL PRIOR TO INSTALLATION. Verify package and hardware contents. Save these instructions.
IMPORTANT SAFETY INFORMATION
1. No parts are serviceable on this product. DO NOT alter anything in this kit other than the
tape light length.
2. DO NOT INSTALL WHILE UNIT IS PLUGGED IN. DO NOT plug the power cord into the
power source until installation is complete.
3. For electrical requirements, see back of driver label.
4. For INDOOR locations only.
5. DO NOT touch, operate, or install fixture while in contact with water. Not intended for
illumination of aquariums.
6. DO NOT mount over sinks or stoves.
7. NOT intended for recessed installation in ceilings or soffits. DO NOT run ANY cords
behind walls, ceilings, soffits, cabinets or a similar permanent structure where it may be
inaccessible for examination.
8. Tape light must be fully uncoiled for proper operation, and to prevent overheating.
Select a location for the LED tape light and mark it. Verify that the power cord reaches the nearest power outlet and will reach the LED tape light. Thoroughly clean the mounting surface
with rubbing alcohol and allow it to dry. DO NOT PLUG THE POWER CORD INTO THE POWER SOURCE UNTIL INSTALLATION IS COMPLETE.
Measure length of the LED tape light carefully before cutting to ensure that the block and corner connectors do not need to be repositioned
as this may affect the performance of the tape light.
ADJUSTING TAPE LENGTHS
The LED tape light can only be cut on the "cut symbol" which is located on
4 in. (10,2 cm) incremental lengths, allowing for cornering and/or custom
installs.
In the event the tape light is cut too short, use an included block connector
(for direct link) or corner connectors (for tight radius corner to rejoin both
segments
ONLY SEGMENTS PREVIOUSLY REMOVED CAN BE ADDED BACK IN. ADDITIONAL TAPE LIGHT LENGTHS CANNOT BE ADDED.
OPTIONAL: BLOCK AND CORNER CONNECTORS
NOTE: Failure to deal the backer
can keep the contacts from
piercing the contact plates
and make it difficult to close
the latches.
NOTE: The polarity symbols
("+"and "-") are located on
the LED tape light every
4 in. (10,2 cm).
Peel back a small amount of the liner of the adhesive tape backer about 0.5 in. (1,27cm). The tape light is polarity sensitive, meaning all
the "+" symbols need to be aligned on one side and all the "-" symbols need to be aligned on the other side of the connections.
To open the connectors latches for use, carefully pry open the latches with a flathead screwdriver.
Line up all the "+" on the LED tape light sections being connected on the same side (as shown). Once the latches are open,
seat the LED tape light sections on top of the contacts. One at a time, close down on the latches until they are locked. The
contacts will pierce the contact plates in the LED tape light to complete the connection.
Model / Modèle / Modelo #: AC1068-WHG-12LF0-G, AC1068-WHG-06LF0-G
12VDC 12VDC
IR (Infrared) Controller
Contrôleur IR (infrarouge)
Controlador IR (infrarrojo)
*Los aditamentos reales pueden diferir de los que se muestran en la ilustración.
WARNINGS AND CAUTIONS
INSTALLATION
NOTE: DO NOT cut the
12VDC
LED tape light strips
anywhere other than the
"Cut Symbol". Doing so
will damage the tape light.
NOTE: Insert the tip of the
12VDC
screwdriver into the gaps between
the connector base and the latches
and twist.
SELF-ADHESIVE TAPE LIGHT KIT (Page 2)
KIT DE RUBANS LUMINEUX AUTOCOLLANTS (Page 3)
KIT DE ILUMINACIÓN CON CINTA AUTOADHESIVA (Página 5)
Corner connector
Connecteur d'angle
Conector de esquina
IR (Infrared) receiver
Récepteur IR (infrarouge)
Remote control
Receptor IR (infrarrojo)
Télécommande
Control remoto
Block connector
Connecteur de bloc
Conector de bloque
*Actual hardware may differ from illustration
*La quincaillerie incluse peut être différente de l'illustration.
9. This tape light is NOT expandable. Additional LED tape light lengths CANNOT be added.
10. DO NOT look directly at lighted LEDs for any length of time.
11. Lights may be installed inside of an enclosure, such as a cabinet, ONLY when the
POWER ADAPTER is located outside of the enclosure.
12. Use only insulated staples or plastic ties (not included) to secure the cords.
13. DO NOT use with an extension cord. Use a power strip with integral over current
protection to supply power to the fixture. NEVER use power strip unless the plug can be
fully inserted.
15. Reattaching the connectors multiple times may damage to the tape light.
16. DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT. If dimmer controls are present,
remove and replace.
17. If unfamiliar with electrical installations, contact a qualified electrician to install.
18. LEDs gradually emit less light over their lifetime.
CUT
SYMBOL
BLOCK CONNECTORS
Align the polarity Symbols
CORNER CONNECTORS
12VDC
Align the polarity Symbols
12VDC
12VDC
Required
Nécessaire
Se necesita
12VDC
The corner connectors are
12VDC
flexible and can be used either
for splicing or navigating tight
radiuses the LED tape light is
unable to form to. DO NOT CUT
the flexible cord.
12VDC