Viega PureFlow V5613.1 Mode D'emploi

Product Instructions
Viega PureFlow Press Polymer
®
ManaBloc Port Adapter
®
Model V5613.1
1 2
7 8
13
EN
Viega PureFlow Press Polymer
ManaBloc Port Adapter
Model V5613.1
Viega products are designed to be
installed by licensed and trained plumbing
and mechanical professionals who are
familiar with Viega products and their installation.
Installation by non-professionals may void
Viega LLC's warranty.
Zero lead identifies Viega products meeting
the lead free requirements of NSF 61-G
through testing under NSF/ANSI 372
(0.25% or less maximum weighted average lead
content).
Square off tubing to proper length. Uneven, jagged, or
1
irregular cuts will produce unsatisfactory connections.
Insert PureFlow Press fitting with attached sleeve
2
into tubing and engage fully.
3
Ensure full tubing insertion at view holes in
attached press sleeve. Full insertion means tubing
must be completely visible in at least two view
holes and partially visible in the one.
Viega LLC
585 Interlocken Blvd.
Broomfield, CO 80021
Phone (800) 976-9819
www.viega.us
3 4
9
10
If using hand tools continue with steps 4 to 6.
If using power tools skip to steps 7 to 10. For
both, continue with steps 11 to 13.
Pressing with a Hand Tool
4
Position the PureFlow press tool perpendicular
over the press sleeve, resting it against the tool
locator ring. For 1" tool, close tool jaws to engage
ratchet (ensure that thumb grip is returned fully
forward before closing jaws). Make sure the
PureFlow press tool is properly aligned.
5
Close handles, using trigger to reduce grip span if
desired.
6
Extend the PureFlow press tool handle and
continue ratcheting until automatic tool release
occurs at the proper compression force.
CAUTION!
Do not press twice.
Pressing with a Power Tool
7
Insert the appropriate PureFlow press jaw into the
press tool and push in the holding pin until it locks.
8
Open jaw and position perpendicular over press
sleeve, resting it against the tool locator ring.
9
Start the pressing process; hold the trigger until
the jaw has automatically released.
10
When press connection is complete, open and
remove the jaw.
CAUTION!
Do not press twice.
11
Ensure sealing element is in place and clean of
any dirt or debris, wet sealing element with tap
water.
Product Instructions
EN
Viega PureFlow Press Polymer
ManaBloc Port Adapter
This document is subject to updates. For the most current Viega
technical literature please visit www.viega.us.
Instrucciones del producto
ES
Adaptador de puerto ManaBloc
de polímero Viega PureFlow Press
Este documento está sujeto a actualizaciones. Para obtener la
documentación técnica más reciente de Viega, visite www.viega.us/es.
Instructions produit
FR
Adaptateur de port Viega PureFlow
Press Polymer ManaBloc
Le présent document est soumis à des mises à jour. Pour consulter
les manuels techniques Viega les plus récents, veuillez visiter
www.viega.ca.
PI-PF 561086 0621 Polymer ManaBloc Port Adapter (EN ES FR)
6 5 6
11 12
12
Insert fitting into desired port until the fitting flange
sets flush with the port.
13
Thread swivel nut onto ManaBloc port. Open the
port valve before turning on the main water supply.
CAUTION!
Hand tighten only.
ES
Adaptador de puerto ManaBloc de
polímero Viega PureFlow Press
Modelo V5613.1
Los productos de Viega están diseñados
para ser instalados por plomeros y
mecánicos profesionales, capacitados
y con licencia, que estén familiarizados con los
productos Viega y su instalación. La instalación
realizada por personal no profesional puede
anular los términos y condiciones del producto
de Viega LLC.
Zero Lead identifica a los productos
Viega que cumplen los requerimientos de
la NSF 61-G mediante la realización de
ensayos de acuerdo a NSF/ANSI 372 (contenido de
plomo promedio ponderado máximo de 0.25 % o
menos).