Special Playback; Recording; Recording A Tv Program - Citizen JVHS3987D Manuel D'instructions

SPECIAL PLAYBACK

TO VISUALLY SEARCH FOR
DESIRED POINTS
When either the F.FWD or REW button is pressed in the
PLAYBACK mode, the speed search picture will appear.
When pressed twice, the search picture will increase
speed. Speed search time depends upon the speed
used (SP, LP or SLP) during recording.
TO WATCH A STILL PICTURE
Press the PAUSE/STILL button in the PLAYBACK mode.
Press the PAUSE/STILL button again to resume normal
playback.
TO WATCH A TAPE REPEATEDLY
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Turn ON the VCR POWER button.
• Press the TV/VCR selector button to select the VCR
mode.
When a TV is connected with an audio/video cable,
turn the TV and this VCR on, and select the video input
mode on the TV.
1
Press the MENU button.
Press the TRACKING SET +
or – button to select the AUTO
REPEAT option.
2
Press the ENTER button to
select the ON position.
3
Press the MENU button.
If you press the PLAY button, the
tape will play over and over until
the repeat mode is canceled.
" " will appear if you press the CALL button.
To cancel, press the CALL button again.
NOTE: To cancel repeat mode, follow the above steps
1 and 2, then press the ENTER button to select
the OFF position. Press the MENU button to
return to the TV.
TAPE SPEED AND
RECORDING/PLAYBACK TIME
You can select the two different tape speed before

recording.

TAPE SPEED
SP
Standard Play
SLP
Super Long Play
This VCR selects the playback tape speed SP,
LP(Long Play) or SLP automatically.
18
MENU
TIMER REC SET
AUTO REPEAT
CH SETUP
SYSTEM SETUP
+/-/ENTER/MENU
á ñ
MENU
TIMER REC SET
AUTO REPEAT
CH SETUP
SYSTEM SETUP
+/-/ENTER/MENU
á ñ
VIDEO CASSETTE TAPE
T120 T160
2 hours 2-2/3 hours
6 hours 8 hours
RECORDING A TV
PROGRAM
RECORDING AND VIEWING THE
SAME TV PROGRAM
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Turn ON the VCR POWER button.
• Press the TV/VCR selector button to select the
VCR mode.
When a TV is connected with an audio/video cable, turn
the TV and this VCR on and select the video input mode
on the TV.
1
Load a cassette tape with the
erase prevention tab intact.
The VCR will automatically
turn on.
2
Press the SPEED selector
button to select the desired
tape speed SP or SLP.
The counter and SP or SLP
will appear on the screen for
about 4 seconds.
VHF/UHF/CATV CHANNELS
ON OFF
TV
VHF
2-13
UHF
14-69
ON OFF
3
Press the direct channel selection buttons or the
CHANNEL
recorded.
1-9
10-19
20-99
100-125 Press the 3 digits in
4
Press the REC/OTR button.
" " will appear on the screen
for about 4 seconds and the
REC indicator will light.
NOTE: Since the VCR has its own TV tuner, it is not
actually necessary to have the TV turned on in
order to make a recording. Turning on the TV
merely allows confirmation of the proper channel
settings on your VCR.
CATV
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100)(125)
01 (5A)
or button to select the channel to be
Press 0 twice and then 1-9 as required.
Example: To select 2, Press "002".
Press 0 first and then the remaining 2 digits in
order from left to right.
Example: Press 012 for "12".
Press 2 digits in order.
Example: Press 22 for
"22".
order.
Example: Press 110
for "110".
00 : 00 : 00 SP
VHF
2-13
+0
+0