XtremeMac LUNA VOYAGER II Guide De L'utilisateur page 4

GETTING STARTED
1. Remove unit and AC adapter from the box and properly
dispose of any protective packaging material.
2. Open battery compartment cover on the bottom of the
unit by sliding it back and lifting up the edge without
the finger slot. Insert 3 AAA batteries as indicated in the
compartment and close cover.
3. Place unit on a level surface close to a power outlet
following the precautions listed in the safety warnings.
4. Locate the back support and insert it into slot behind
the dock connectorby aligning the groove with the rear
support. Push down until an audible snap is heard. This
will lock the rear back support into place.
5. Untie and extend the FM antenna connected on the back
of unit for best reception.
TO DOCK IPOD, IPHONE, IPAD
Pull dock towards the display to lock into place.
Dock iPod, iPhone, iPad onto dock and rest against back
support.
Dock is designed to lock and rotate in order to work with
iPod, iPhone, iPad still in most protective cases.
PLUGGING IN THE UNIT
1. If located in the US, skip to step 5. If located outside
the US, select the appropriate wall adapter. If already
attached to the unit, skip to step 5.
2. Using a small object like a pen, press the button under
the wall adapter to release the adapter.
3. Gently slide in the appropriate wall adapter. You will
hear a click when it is properly locked into place.
4. Connect the AC adapter jack to the back of the unit
labeled 12V and then connect the other end of the
adapter to a power outlet.
5. When the unit is first powered on. The Display will show
'LUNA' for 5 seconds and be in standby mode.
6
BASIC OPERATION
Press SNOOZE/SOURCE to cycle through iPod -> Radio -> Aux
-> STANDBY
To automatically enter standby mode from iPod, Radio or
Aux modes, press and hold SNOOZE/SOURCE for 2 seconds.
DIMMER SETTING
Display brightness can only be adjusted in standby mode or
by the app in all modes.
In order to meet EuP requirements the display brightness is
defaulted to mid level.
To adjust display brighness while in standby mode press (+)
to increase and press (-- ) to decrease.
There are four settings: High/Mid/Low/Off.
Note: If the display brightness is off when the alarm sounds,
the display brightness will be changed to mid setting.
Unit display brightness will automatically be set to mid
upon entering the standby mode.
VOLUME UP / DOWN
Press (+) to increase the volume and press (--) to decrease
the volume (0 to 20). The number will be visible on the
display during this adjustment. It will time out after 2
seconds.
Volume can be adjusted in all playback modes.
Default volume level is set to level 10 for 1st time usage.
The volume level will be remembered when the unit is
switched to standby mode and will resume when the unit
is switched to a playback mode.
SETTING THE TIME WITH IPOD, IPHONE, IPAD
Dock either iPod/iPhone/iPad and the unit will
automatically set the time from device. Use of 12 or 24 hrs
will also follow iPod/iPhone/iPad after synced.
Note: Time Sync function can be used from most of the iPod/
iPhone/iPad models, except some old models such as iPod
mini, iPod 3G, 4G. Clock time of main unit itself is default at
12 hours
If time does not set automatically when an iPod/iPhone/
iPad is docked, the clock will need to be set manually.
SETTING THE CLOCK MANUALLY
(IN STANDBY MODE ONLY):
To set the clock time manually:
1. In standby mode, press and hold SNOOZE/SOURCE for 2
seconds to enter the clock setting mode.
2. The hour will blink, Press (+) to increase the hour or (-- )
to decrease the hour (or press and hold either (+/-- ) to
fast tune). Press SNOOZE/SOURCE once to confirm, then
minute will blink.
Note: Be sure to observe the AM indicator on the display to
ensure the proper time is set correctly
3. Press (+) to increase the minute or (-- ) to decrease
the minute (or press and hold (+/-- ) to fast tune). Press
SNOOZE/SOURCE once to confirm and exit the clock
settings mode.
ALARMS
To set the alarm time:
1. In standby mode, press and hold 1 /2 for 2 seconds to
enter the alarm setting mode.
2. The hour will blink, Press (+) to increase the hour or (-- ) to
decrease the hour (or press and hold (+/-- ) to fast tune).
Press 1 /2 once to confirm, then minute will blink.
3. Press (+) to increase the minute or (-- ) to decrease the
minute (or press and hold (+/-- ) to fast tune). Press 1 /2
once to confirm.
4. The current alarm source will blink (iPod by default), press
(+) or (-- ) to select iPod or Radio or Chime, press 1 /2 once
to confirm, then the volume setting will blink.
7