Sensede DEEP RELAX CP40S Mode D'emploi page 3

EN
CP40S - HEATING PILLOW
BOX CONTENT
HEATING PILLOW
PARTS
Power inlet socket
Power connector plug
INTENDED USE
Your Sensede heating product is designed to provide comfortable warmth. The appliance operates on
220-240V, 50Hz (mains electricity). Never try to connect the appliance to other power sources. Please always
follow the safety instructions in this manual. Keep this instruction manual in a safe place so that it is available
at all times. This product complies with regulatory, national and European requirements. Never try to make
technical modifications to this device. We do not accept liability for accidents or damages resulting from
failure to follow these operating and safety instructions.
WHAT TO EXPECT
The Sensede CP40S is a heating pillow with an integrated electrical warming circuit. It can be used when you
are feeling cold, need help relaxing muscles or require targeted pain relief in muscles or joints. It is designed
for comfort and pain relief. The 3-level control unit allows you to set the desired warmth level. The appliance
is designed to warm up quickly. The product is made with super soft, cosy fleece material that is pleasant to
the skin and can be hand washed at 30°C. For your safety, the product is equipped with a smart overheating
sensor and an automatic 90 minute timer.
BEFORE YOU START
Please carefully read the safety instructions in this manual before getting started.
CONNECTING THE CONTROLER
To connect the control unit, plug the power connector plug into the power inlet. Make sure to fully insert the
connector. If you notice the control unit light blinking after switching on the appliance, the connector plug
OK
may not be correctly inserted.
✔
not ok
CORRECT
CONTROL UNIT
UHB100EU
CP40S
Control unit
Mains plug
INCORRECT
SELECTING A WARMTH LEVEL
You can switch on the appliance and select the desired warmth
setting by sliding the selection button on the control slider upwards.
The selected level (1-3) will light up. You will generally notice the
device becoming warm within 30 seconds. Slide the button back
down to lower the warmth setting or to switch off the device
(no number lit).
Settings:
1.) Minimum warmth (recommended for prolonged use)
2.) Medium warmth
3.) Maximum warmth (fast warm-up)
We recommend disconnecting the appliance from mains electricity
when it is not in use. When first using the appliance a 'new plastic'
smell may be noticeable. This will disappear over time.
INSTRUCTION
MANUAL
90 MINUTES SAFETY TIMER
This appliance has an automatic timer. After 90 minutes of continuous use, it will automatically power down.
To reactivate it, switch off the device as normal and wait approx. 5 seconds before reactivating it.
WASHING AND CARE
Always disconnect the appliance from mains electricity before cleaning operations.
Control unit and cable
- The control unit and cable can be gently cleaned with a soft cloth.
- The control unit and cable should never be exposed to water or other liquids.
Pillowcase
- Caution: Never switch on the appliance when the heating pillow is wet/damp.
- The pillowcase can be hand washed at 30°C if it appears unclean.
- Use a mild detergent for delicate textiles. Do not use aggressive cleaners, bleaching agents or abrasives.
- Drying: Air dry flat only. Never machine dry. Do not iron or wring out. Do not use clothing pegs.
- Do not wash too often. Washing will, over time, cause extra wear to the materials. We recommend hand
washing your heating pillow cover a maximum of 12 times during its service life.
TROUBLESHOOTING
The LED number indicator on the control unit is blinking, and there is no warmth. What could be
the cause?
- The control unit senses that the power connector plug is not (properly) connected. Switch off the appliance
and reconnect it. Please disconnect from mains electricity while reinserting the power connector plug.
The appliance will not switch on, and no number lights up. What could be the cause?
- Check if the appliance is plugged in.
- The control unit may have been disabled by the internal safety system. When the internal safety system
detects a critical malfunction in the heating circuit, it prevents the appliance from heating up. Please do not
use the appliance if it is malfunctioning or damaged and contact our service team.
✘
Level selection
LED
Control
slider
let's make your life better