Laurus LCA78ZKB Notice D'utilisation page 115

pessing , "00" is displayed and shows
that timer is active. The dot in the Timer
Display indicates that
be used to set the timer value.
The minute minder can be selected when
all Cooking Zone Indicators are on or off
(no Cooking Zone Indicator is flashing).
With and , the timer value can be set.
The minute minder timer begins counting
down once it has been set.
The minute minder cannot be stopped by
switching off the appliance or activating the
key lock function, it will continue to count
down.
After reaching the "00", the timer, buzzer
sounds. To stop the buzzer, press any
button.
Heater timer
Heater timers can be set only for activated
heaters (heater level must be set between
1-9).
The first touch of
minute minder. After touching
second time, the timer is assigned to the
activated heater. This is indicated by the
corresponding Cooking Zone Indicator
flashing.
Touching again after activating the first
heater timer, activates the timer for the next
active heater in a clockwise direction. This
is indicated by the flashing Cooking Zone
Indicator.
Pressing and
the timer value for the heater.
The timer for the heater that was set first is
indicated by the illuminated Cooking Zone
Indicator.
Touching once again allows further
timers to be assigned to other activated
heaters.
10 seconds after the last operation, the
timer display changes to the timer that
will run out next. The assignment of the
timer is displayed by a flashing Cooking
Zone Indicator. The number of timers that
are running is indicated by the number of
cooking zone indicators that are illuminated.
By toggling , you can display the timer
values for the heater timer and the minute
minder. The assignment is always indicated
by the flashing Cooking Zone Indicator.
If no Cooking Zone Indicator flashes, the
minute minder time is shown in the 2-digit
Timer Display.
All heater timers can be cleared by
and can now
, activates the
for a
, will allow you to set
switching the appliance into S-Mode using
. A minute minder will not be cleared, it
will continue to count down,
To clear a timer in Operation Mode, you
first have to select the timer by toggling the
Activate/Deactivate Timer Button until it is
displayed. The value can be cleared in 2
different ways:
• Decrement, by pressing
appears on the Timer Display.
• Press
seconds until "00" is shown in Timer
Display.
Once a timer reaches "00", the
corresponding heat level will be set to "0".
The end of a heater timer or the minute
minderis indicated by a buzzer This can be
stopped by pressing any button.
Key Lock
The key lock function is used to set
'save mode' on the appliance during
operation. It will not be possible to make
any adjustments by touching the buttons
(for example heat settings). It will only be
possible to switch the appliance off.
The lock function is active, if the Key
Lock button
seconds. This operation is acknowledged
by a buzzer. After successful operation, the
key lock Indicator flashes and the heater is
locked.
The heater can only be locked in Operating
Mode (B-Mode).
If the heater is locked, only the
can be used. All other buttons are blocked.
If any other button is pressed in the blocked
mode, the buzzer sounds and the Key Lock
Indicator flashes. Only the switch off by
operation by using
if you switch off the appliance, you can not
restart it again without unlocking.
After pressing
Lock Indicator disappears. Now, the hob
control is unlocked and can be operated in
normal order.
Child Lock
Child lock functionality is used to lock the
appliance in a complicated multi-Step
process. Child lock (and unlocking) is only
available in the S-Mode.
First has to be pressed until the buzzer
beeps, then
simultaneously for at least 0.5 seconds, but
no longer than 1 sec. Following that, the
appliance can be locked by touching
EN - 15
until "00"
and simultaneously for 0.5
is pressed for at least 2
is possible. However,
for 2 seconds, the Key
and have to be pressed
button
. All