KIKKA BOO O'RIGHT Mode D'emploi page 9

4. INSTALLATION FOR GROUP I
ATTENTION!!!
• The installation for Group I is forward facing and child's body weight have to be over 9kg and less than 18kg.
• There are 3 adjustable levels in Red 1/2/3.
• After adjusting the angle, the safety seat has to cling to car seat back and pull car safety belt tight.
4.1. Push the red knob to adjust the angle of seat to one of three levels before starting installation.
4.2. Place the safety seat forward in the car seat and make it cling to car seat back.
4.3. As shown in the picture 4.3(1), 4.4(1) the car safety belt passes through the hole of the safety seat according to the red direction. As shown in the picture
4.3 (2), put the car safety belt tongue into the car buckle. As shown in the picture 4.3(2), pull horizontal car belt tight and place oblique car belt into locking
device, then pull belt tight again,put remainder belt into seat belt retractor. Finally, shake the safety seat to ensure it is already xed.
5. USING METHOD FOR GROUP 0+/I
5.1. Press Central Adjuster and pull harness.
5.2. Press red button to open the harness strap outward at the same time to make buckle the strap loose.
5.3. Pull out both of the shoulder belts to both sides of the child safety seat, or insert buckle tongues into xed slots.
5.4. Place your child into seat and make sure the lap belt can restrict the position of pelvis. Please check the height of shoulder
belts. It is better to make shoulder belts be a little bit higher than child's shoulders.
5.5. Harness Buckle: put the two latches together and engage them before putting them into the harness buckle, you can hear a click noise. The buckle latches
will be released if you press the red button.
5.6. Adjust the straps by pull harness adjustment strap outward and make sure that the tightness is comfortable for your child.
5. 7.The shoulder belt height adjuster: before adjustment, remove base plate rst. According to di erent heights of children, 4 levels of shoulder belt heights
can be adjusted. Firstly, as shown in picture (1,2,3), separate the shoulder safety belt with strap yoke, and then according to (4,5), separate the shoulder belt
with harness yoke and correspond to the appropriate harness slots to insert both of shoulder safety belts (6). Finally, connect both of the safety belts as shown
in gures (1,2,3,4,5)
5.8. Caution: Do not twist the belts.
5.9. Adjusting the height of pillow to t children's head.
6. REMOVAL OF 5-POINT HARNESS
6.1. Adjusting the angle of safety seat to level 4, press central adjuster and maximum loose the shoulder belts. Then, remove the bracket in the bottom of
safety seat and separate it with safety belt.
6.2. Firstly, before adjustment, remove base plate. As shown in picture (1,2,3), separate the shoulder safety belt with strap yoke, and then according to (4,5),
separate the shoulder belt with harness yoke and pull harness strap out; then, pull the strap with buckle out of the seat as well (6). Next, pull harness
adjustment strap tight and hide strap under cloth cover. Finally, you can storage harness strap.
7. INSTALLATION AND USING METHOD FOR GROUP II
ATTENTION!!!
• Only one adjustable level for Group II is Red Level 1.
• Before Installation for Group II, remove 5-point harness and cushion
• Pull car safety belt tight and make sure car belt tongue insert car buckle correctly.
Place your child into seat and make oblique car belt pass through red guiding
hook for Group II (1). Then, make horizontal car belt pass through red harness guider for Group II (2 & 3). Next, car belt tongue insert car buckle correctly and
you can hear click noise (4). Finally, make sure the lap belt can restrict the position of pelvis.
8. REMOVING THE COVER
Separate the shoulder safety belt with strap yoke, and then separate the shoulder belt with harness yoke. Open harness buckle and take of cloth cover from
safety seat.
CAUTION!!! When you want to re t the cover, just take steps in the opposite order.
9. CLEANING AND MAINTAINING
• Check all components of safety seat regularly and if the accident happens, you have to replace a new safety seat.
• Storage safety seat in a dry, ventilative and cool place when it is not used for an extended period of time.
• If food or beverage makes the safety belt dirty, remove the belt and rinse using warm water and make it dry by airing.
• If wash the whole cloth cover, please refer to the washing instructions.
• If wash the cover in the rst time, the cover might fade a little bit. It is a normal phenomenon.
10. WASHING INSTRUCTIONS
CAUTION!!! Do not use solvents, chemical cleaners and lubricants.
Hand wash using the water temperature under 30ºC. Do Not Bleach. Dry clean, use the detergents excluded trichloroethylene.
Do Not Machine Dry. Do not Iron.
ENGLISH