GOLIATH-BIKE GOLIATH RACE Manuel De L'utilisateur page 2

INSTRUCTIONS FOR USE:
1 - Loosen the clamp [4] of the stand, lengthening or shrinking the extensible manually, set the
clamp [1] to the desired height and re- x the up/down lock [4].
2 - Loosen the side loop [3] of the clamp and place it horizontally, x the clamp moderately.
3 - Once we have the clamp at the desired height, horizontal, open and xed we can proceed to
raise the bicycle manually, when we support the bicycle on the clamp we proceed to tighten the
clamp [2] according to the type of frame.
4 - Once the bicycle is supported by the clamp, loosen the lateral lever [3], look for the necessary
angle according to the inclination of the frame or the work to be done, x the lever [3] of the
clamp to maintain the desired angle.
5 - The clamp does not have a clamping stop [2], the user must determine the pressure required
according to the work to be performed and the type of frame to be clamped.
It is important to know the type of frame to be clamped, since carbon frames are weaker to
clamping.
*For this type of frame there is a special clamp (GOLIATH 360º CARBON) that allows to cover
more frame surface and reduce the e ort per square centimeter, it also has a softer polyurethane
protection designed to prevent the frame from rolling even with less pressure.
(See our product catalog)
6 - With the bicycle raised we can turn it on the axis of the clamp looking for the desired
position.
For this operation we only have to loosen the side loop [3] that xes the clamp.
Once the bicycle is in the desired position, proceed again to tighten the side loop so that it
remains xed in that position.
7 - Whenever we intend to turn 180º (or another angle) we must make sure that the clamp has
the necessary pressure [2] on the frame so that it does not roll and can tip over to the sides.
To return to the initial position, just loosen the side loop [3] again and, holding the bike, rotate it
to its at position or the angle you want.
It is very important for this operation of turning the bike 180º to be easy and with little e ort,
that when holding the bike you look for the closest center of gravity of the bike.
8 - Once you have nished with the lifting work and you want to lower the bike to its starting
position, you should look for the horizontal plane of the clamp before opening it, once open you
can lower the bike manually.
9 - GOLIATH G2-RACE is ready to install all the extras of the GOLIATH BIKE line.
WARNINGS OF DANGER IN THE USE OF THIS SUPPORT:
1- Always place the bicycle on the stand as centered as possible, always looking for the approximate center of gravity.
2- Under no circumstances hold the bicycle by the ends.
3- Always hold the clamp in rigid areas of the frame, avoiding plastic or other weak areas.
4- The support must not be operated by children, only by adults.
IT IS FORBIDDEN TO WORK UNDER THE LIFTED LOAD WITHOUT SECURING IT WITH APPROPRIATE ADDITIONAL MEANS.
WARNINGS IN CASE OF REPAIR OF THE GOLIATH G2-RACE STAND:
1- Only use spare parts from the manufacturer or authorized supplier.
2- The manufacturer cannot be held responsible for any modi cations made without prior authorization from the manufacturer.
3- Only use the GOLIATH G2-RACE stand according to the manufacturer's instruction manual.
4- Only carry out maintenance and repairs in accordance with the manufacturer's instruction manual.
5- Repairs and maintenance may only be performed by quali ed personnel.
MAINTENANCE:
1 - The bracket does not require any speci c maintenance.
2 - The only greasing point may be the clamp holder and the clamping clip, which must be lubricated with a little grease,
vaseline, etc.
This greasing process should be done at the user's discretion and although it is not necessary, it does contribute to smoother
movements.
WARNING
THE CLOSING PRESSURE OF THE 360º BASIC CLAMP MUST BE DETERMINED
BY THE USER FOR ITS CORRECT OPERATION.
GOLIATH BIKE WILL NOT BE HELD RESPONSIBLE FOR ANY DAMAGE CAUSED
TO THE FRAME OR ANY PART OF THE BICYCLE DUE TO MISUSE OF THE 360º
BASIC CLAMP, THE USER BEING SOLELY RESPONSIBLE.
IN NO CASE SHOULD THE 360º BASIC CLAMP (G-AC014) BE USED TO HOLD
CARBON FRAMES. FOR THIS WE HAVE THE 360º CARBON CLAMP DESIGNED
EXCLUSIVELY TO EXERT LESS PRESSURE AND NOT DAMAGE CARBON FRAMES.
GOLIATH BIKE manufactured by:
METSISTEM ELDA S.L.
Los Cisnes 12, Elda (Alicante), España
NIF: B54557798
info@goliath-bike.com
WWW.GOLIATH-BIKE.COM