EarthWise LB20058 Manuel De L'utilisateur page 4

TO TURN THE TOOL ON
Slide on/off switch forward to "ON" position. To turn the tool OFF, slide
backward to "OFF" position.
WARNING: Do Not use the blower with any type of accessory or attachment.
Such usage might be hazardous.
AIR SPEED CONTROLS
Rotate the speed control Wheel to accelerate or decelerate air speed. By
pressing turbo button, air speed will immediately accelerate to maximum level.
(See fig. 2)
BLOWING
Blower can be used to clean corners, fences, walls, wooden areas or beneath
cars. Be careful how you point the jet of air as it could move heavy material and
cause injury or damage.
Turn the switch to on, point the jet of air in front of you and move forward slowly
to gather together the leaves or to move the leaves from inaccessible areas.
WARNING: After battery has been fully depleted, make sure switch is in the
"OFF" position.
Avoid collisions with hard objects which could damage your blower.
Keep bystanders and animals at least 15 feet (5 m) away from the working
area.
If you drop the blower, carefully inspect it for damage. If the tube is broken,
housing cracked, or handles broken or if you see any other condition that
may affect the blower's operation, call our customer service help line at
1-800-313-5111 for assistance.
To clean the tool, make sure the battery is detached from the unit, then use
only mild soap and a damp cloth. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment should be performed by an authorized service
center or other qualified service organization, always using identical
replacement parts.
CAUTION: Do not at any time let brake fluids, gasoline, petroleum based
products, penetrating oils, etc., come in contact with plastic parts. They
contain chemicals that can damage, weaken or destroy plastic.
Fertilizers and other garden chemicals contain agents which greatly
accelerate the corrosion of metals. Do not store the tool on or adjacent to
fertilizers or chemicals.
Problem
- Unit does not run
- Battery will not charge
MAINTENANCE
TROUBLESHOOTING
Possible Cause
- Battery not making contact
- Battery not installed properly
- Battery not charged
- Battery not inserted into charger
- Charger not plugged in
- Surrounding air temperature too hot or too cold
OPERATING
Make sure that the switch is in "OFF" position, the battery pack is
disconnected and all the rotating parts are at a standstill before
cleaning, carrying out inspections or moving from one place to
another.
Do not put part of your body such as hands and fingers in the
exhaust opening.
Do not switch the machine on in enclosed or poorly ventilated
spaces or in the presence of flammable and/or explosive
substances such as liquids, gas and powders.
STORING THE BLOWER
Clean the blower thoroughly before storing. Store the blower in a
dry, well-ventilated place that is inaccessible to children. Keep
away from corrosive agents such as garden chemicals and
de-icing salts.
■ Store and charge your batteries in a cool area. Temperatures
above or below normal room temperature will shorten battery
pack life.
■ Never store batteries in a discharged condition. Wait for
battery pack to cool and fully charge immediately.
■ All batteries gradually lose their charge. The higher the
temperature, the quicker they lose their charge. If you store your
unit for long periods of time without using it, recharge the
batteries every month or two. This practice will prolong battery
pack life.
■ Recharge batteries every 3 months.
When not in use, your Cordless Blower should be stored indoors
in a dry and high or locked-up place, out of reach of children.
- Check battery is fully inserted
- Check that battery is securely connected to the blower
- Check battery charging requirements
- Insert battery into charger until LED appears
- Plug charger into a working outlet
- Check current at receptacle by plugging in a lamp or other
appliance
- Check to see if receptacle is connected to a light switch which
turns power off when you turn out the lights
- Move charger and tool to a surrounding air temperature of
above 32 degree F (0 degree C) or below 100 degree F ( +37.8
degree C)
4
Turbo button
Possible Solution
Fig. 2