Bullfrog Spas I Serie Guide De Référence Rapide

Quick Reference Guide for Bullfrog Control System
F1 F1
time time warmer warmer
F2 F2
PL PL
TL TL
mode/prog mode/prog cooler cooler
INITIAL START-UP
When you power up the spa, it will begin the Priming mode. The Priming mode will
last for up to 4 minutes. To exit Priming mode early press WARMER or COOLER.
SPA MODES
Press MODE/PROG to enter mode programming.
1.
Press COOLER to cycle through modes.
2.
Press MODE/PROG to confirm.
3.
This multi-button sequence allows you to switch between the following modes:
Standard: maintains desired temperature.
•
Economy: heats spa to set temperature only during filter cycles.
•
Sleep: heats spa to within 20ºF of set temperature only during filter cycles.
•
STANDBY MODE
Standby mode prevents spa from turning on while changing filter cartridge or JetPaks
Press WARMER.
1.
Press JETS 2 or AUX.
2.
Press any button to exit.
3.
TEMPERATURE
To increase or decrease the set temperature:
Press WARMER or COOLER button once to display the set temperature.
1.
2. Press WARMER or COOLER to increase or decrease the temperature.
ADJUSTING FILTER CYCLES
Please refer to the Premier Control system section in the Owner's Manual.
CONTROL PANEL LOCK
To lock Control Panel press: TIME, JETS 1 then WARMER (PL light is on when locked)
To Unlock Control Panel press: TIME, JETS 1 then COOLER.
JETS 1
Pump 1 high-speed will turn off automatically after 30 minutes and low-speed will turn
off automatically after 4 hours.
1. Press JETS 1 to turn on pump 1.
Press JETS 1 to shift between low and high speeds.
2.
Press JETS 1 again to turn off jets.
3.
Note: Jets 1 will not turn off if the spa is in filtration mode or heating.
JETS 2 (optional)
See Jet 1
Note: An optional auxiliary control button on the side of the spa can activate
either pump.
LIGHT
Press LIGHT to turn light on and off. The light will turn off automatically after 1 hour.
LED LIGHT (optional)
The light will turn off automatically after 1 hour.
Press LIGHT to turn on light.
1.
Press LIGHT again to shift through color options.
2.
Note: Only pause 2-3 seconds in between color selection.
TIME
To set or change the time:
Press TIME then MODE/PROG.
1.
Press either WARMER or COOLER to adjust hour.
2.
Press MODE/PROG to switch to minutes.
3.
4. Press TIME to confirm.
REMINDERS
To dismiss maintenance reminders, press WARMER or COOLER and then LIGHT.
TM
light light option option
jets 1 jets 1 jets 2 jets 2
Series I
jets 2 or aux
INITIAL START-UP
When you power up the spa, it will begin the Priming mode. The Priming mode will
last for up to 4 minutes. To exit Priming mode early press WARM or COOL.
SPA MODES
1. Press MODE to enter mode programming.
Press COOL to cycle through modes.
2.
Press MODE to confirm.
3.
This multi-button sequence allows you to switch between the following modes:
•
Standard: maintains desired temperature.
•
Economy: heats spa to set temperature only during filter cycles.
•
Sleep: heats spa to within 20ºF of set temperature only during filter cycles.
STANDBY MODE
.
Standby mode prevents spa from turning on while changing filter cartridge or JetPaks
®
Press WARM or COOL.
1.
Press JETS 2 /AUX.
2.
3. Press any button to exit.
TEMPERATURE
To increase or decrease the set temperature:
Press WARM or COOL once to display the set temperature.
1.
Press WARM or COOL to increase or decrease the temperature.
2.
ADJUSTING FILTER CYCLES
The factory preset filter cycle is 2 hours every 12 hours.
Press WARM or COOL then JETS 1.
1.
Press WARM or COOL to select the filter duration.
2.
Press JETS 1 to select the number of filter cycles.
3.
Press WARM or COOL to modify.
4.
Press JETS 1 to exit program.
5.
JETS 1
Pump 1 high-speed will turn off automatically after 30 minutes and low-speed will turn
off automatically after 4 hours.
Press JETS 1 to turn on pump 1.
1.
Press JETS 1 to shift between low and high speeds.
2.
Press JETS 1 again to turn off jets.
3.
Note: Jets 1 will not turn off if the spa is in filtration mode or heating.
JETS 2 (optional)
See Jets 1.
Note: An optional auxiliary control button on the side of the spa can activate
either pump.
LIGHT
Press LIGHT to turn light on and off. The light will turn off automatically after 1 hour.
LED LIGHT (optional)
The light will turn off automatically after 1 hour.
Press LIGHT to turn on light.
1.
2. Press LIGHT again to shift through color options.
Note: Only pause 2-3 seconds in between color selection.
REMINDERS
To dismiss maintenance reminders, press WARM or COOL and then LIGHT.
Series II
(Refer to the Owner's Manual for more information)
.
®