Salora 32LED9112CSW Mode D'emploi page 39

For connecting to a wireless LAN network, you
should perform the following steps:
1. Connect broadband ISP connection ethernet
cable to the ETHERNET INPUT of your modem.
2. Ensure that Nero Media Home software is
installed to your PC (for DLNA function).
3. Afterwards, you should connect wireless adaptor
to one of the USB inputs of the TV.
4. To configure wireless settings please refer Network
Settings section in the following sections.
• A Wireless-N router (IEEE 802.11a/b/g/n) with
simultaneous 2.4 and 5 GHz bands designed to
increase bandwidth. Optimized for smoother and
faster HD video streaming, file transfers, and
wireless gaming.
• Use LAN connection for quicker file sharing between
other devices like computers.
• The frequency and channel differ depending on the area.
• The transmission speed differs depending on the
distance and number of obstructions between the
transmission products, the configuration of these
products, the radio wave conditions, the line traffic,
and the products that you use. The transmission
may also be cut off or get disconnected depending
on the radio wave conditions DECT phones, or any
other WiFi 11b appliances. The standard values of
the transmission speed are the theoretical maximum
values for the wireless standards. They are not the
actual speeds of data transmission.
• The location where the transmission is most effective
differs depending on the usage environment.
• Wireless LAN adaptor should be connected directly to the
TV's USB port. USB hubs are not supported.
• Wireless LAN adaptor supports 802.11 a,b,g & n type
modems. It is highly recommended that you should
use IEEE 802.11n communication protocol in order
to avoid any possible problems while watching videos.
• Use the other usb input, if you experience problems
with audio/video performance.
• You must change your modem's SSID when there
are any other modems around with the same SSID.
Configuring Network Settings
Your TV's Network Settings include Wired and Wireless
Connection options. However, if your TV does not have
USB Wi-Fi dongle, you should use Wired Connection
type. If you try to connect via Wireless Connection when
your TV does not have a USB Wi-Fi dongle, a warning
screen will appear and the TV will not get an IP address.
Try connecting the LAN cable after this and then the TV
will be able to get an IP address.
Configuring Wired Device Settings
If you are connecting the TV via ETHERNET INPUT,
select Network Type as Wired Device to configure.
Network Type
Network type can be selected as Wired or Wireless
device, in accordance with the active connection to the
TV set. Select this as Wired if you have connected to the
TV a LAN cable. Select as Wireless if you connect via
the wireless USB dongle.
Configuration Status
This section displays the status of the connection.
IP Address
If an active connection is available, the IP address will
be displayed on this section. If you want to configure IP
address preferences, press GREEN button and switch
to the advanced mode.
Configuring Wired Network Settings in
Advanced Mode
While in Advanced Mode, press RED button to edit
settings. When finished, press OK to save, Press
RETURN/BACK to cancel.
IMPORTANT: "Veezy 200" USB dongle is required to
use wireless network feature.
Wi-Fi feature can be used for a wireless network
connection. If you have the Veezy 200 Wifi Dongle,
select Network Type as Wireless Device to start
connection process.
To enable Wi-Fi feature, profiles should be configured
properly. Please plug in the Wi-Fi dongle to one of the
USB ports.
Press YELLOW button to scan wireless network.
Afterwards, available network list will be displayed.
Please select your desired network from the list.
If the selected network is protected with a password,
please enter the correct key by using the virtual
keyboard. You can use this keyboard via navigation
buttons and OK button on the remote control.
Wait until the IP the address is shown on the screen.
This means that the connection is now established. To
disconnect from a wireless network, you should highlight
Configuration Status and press OK.
English - 61 -