Télécharger Imprimer la page

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

FITTING INSTRUCTION
Clamp mark
in acc. with
Cables joining
ISO
PN
1
L
Left directional lights
2
+
Rear fog lights
3
31
Ground
4
R
Right directional lights
5
58R
Right side parking lights
6
54
Stoplights
7
58L
Left side parking lights
12
18
6
12
9
5
7
13
8
This towbar is designed to assembly in following cars:
RENAULT CLIO I, 3/5 doors, catalogue no. G34 , produced since 1990
till 02.1998 and is prepared to tow trailers max total weight 1100 kg and
max vertical load 75 kg.
Thank you for buying our product. Their reliability has been
confirmed in many tests. Reliability of towbar depends also on correct
assembly and correct exploitation. For this reasons we kindly ask to read
carefully this instruction and apply to hints.
The towbar should be install in points described by a car producer.
6
18
1
10
3
From manufacturer
1. Take out the spare wheel.
2. Disassemble the bumper.
3. To the left and right chassis member put 4 basket nut (pos. 9) – per 2 a
4
side, in original prepared holes .
14
4. Put side brackets (pos. 4 and 5) to the frame and fix by bolts M8x30mm
(pos. 14) and with basket nut in members (loosely) as show in the
drawing.
7
5. Through original holes in the frame put sleeve (pos. 6) with washers
(pos. 18) and fix to brackets (pos. 4 and 5) using bolts M10x80mm (pos.
12) as shown in the drawing.
6. To fastened brackets fix body of the towing hitch (pos. 1) by bolts
M10x40mm (pos. 13). Take a note of sleeve (pos. 7 and 8) placement,
see drawing.
11
7. Reassemble the bumper (Without three bolts in central part of the
bumper – place lack).
8. Fix tow ball (pos. 2) using bolt M12x75mm (pos. 10) and M12x70mm
(pos. 11). With bolt M12x75mm fix also a socket plate (pos. 3). See
figure 1.
9. Tighten all bolts according to the torque shown in the table.
10. Connect electric wires of 7-pole socket according to the instruction of
2
the car. (Recommend to make at authorized service station)
11. Complete paint layer damaged during installation.
After install the towbar you should get adequate note in registration book
(at authorised service station).The car should be equipped with:
• Indicators
• Tow mirrors
After 1000km check all bolts and nuts. The ball of towbar must be always
kept clear and conserve with a grease
Assemble instruction
Torque settings for nuts and bolts (8,8):
M 8 - 25 Nm
M 10 - 55 Nm
M 12 - 85 Nm
M 14 - 135 Nm
NOTE
.

Publicité

loading

Sommaire des Matières pour AUTO-HAK G34

  • Page 1 11. Complete paint layer damaged during installation. This towbar is designed to assembly in following cars: Torque settings for nuts and bolts (8,8): RENAULT CLIO I, 3/5 doors, catalogue no. G34 , produced since 1990 M 8 - 25 Nm M 10 - 55 Nm till 02.1998 and is prepared to tow trailers max total weight 1100 kg and...
  • Page 2 Towbar accessories: PPUH AUTO-HAK S. J. Produkcja Haków Holowniczych Henryk & Zbigniew Nejman 76-200 SŁUPSK ul. Słoneczna 16K tel/fax (059) 8-414-414; 8-414-413 E-mail: office@autohak.com.pl www.autohak.com.pl Towing hitch (without electrical set) Cat. no. Class: A50-X Technical data: Designed for: D-value: 6,04 kN...
  • Page 3 Le dispositif d'attelage à boule est conçu pour être monté dans la voiture: RENAULT CLIO I, 3/5 portes, produit à partir de 1990 au 02.1998, numéro de catalogue G34 et est utilisé pour tirer des remorques du poids total 1100 kg et de Attention la pression totale sur la boule max 75 kg.
  • Page 4 PPUH AUTO-HAK ż.J. Equipement du dispositif d'attelage à boule: Fabrication des dispositifs d'attelage à boule Henryk & Zbigniew Nejman 76-200 SŁUPSK ul. Słoneczna 16K tel/fax +48 (59) 8-414-414; 8-414-413 E-mail: office@autohak.com.pl www.autohak.com.pl Dispositif d'attelage à boule sans équipement électrique Numéro de catégorie.
  • Page 5 M 12 - 85 Nm M 14 - 135 Nm RENAULT CLIO I, 3/5 drz., odkręcana kula, numer katalogowy G34, produkowanego od 1990 do 02.1998r. i słuŜy do ciągnięcia przyczep o masie całkowitej do 1100 kg i nacisku na kulę max 75 kg.
  • Page 6 WyposaŜenie zaczepu: PPUH AUTO-HAK S. J. Produkcja Zaczepów kulowych Henryk & Zbigniew Nejman 76-200 SŁUPSK ul. Słoneczna 16K tel/fax (059) 8-414-414; 8-414-413 E-mail: office@autohak.com.pl www.autohak.com.pl Zaczep kulowy bez wyposaŜenia elektrycznego Nr kat. Dane techniczne: Klasa: A50-X wartość D: 6,04 kN...