Publicité
Les langues disponibles
Les langues disponibles
B E D I E N U N G S A N L E I T U N G
OPERATING INSTRUCTIONS
Oil pressure meter
Order no.:
84 20 95
This product complies with the applicable national and European specifications.
Intended Use
The oil pressure meter serves for displaying the motor oil pressure in vehicles
This product may only be operated if it is connected to a 12V DC car power supply with the negative terminal of the car
battery connected to the body. It may only be installed and operated in vehicles supplied with this kind of voltage. Never
connect the device to any other power supply.
Use is only permitted inside the car, not outside. Contact with moisture or dampness must be avoided at all times. The user
must make sure that the way the product is installed protects the product from humidity and wetness.
Any use other than that described above will damage this product and involves the risk of short circuits, fire, electric shock,
etc.
No part of this product may be modified or rebuilt.
The safety instructions must be observed at all times.
Safety and Hazard Notices
The guarantee/warranty will be void if damage is incurred resulting from non-compliance with
these operating instructions. We do not assume liability for any consequential damage.
We shall not accept liability for damage to property or personal injury caused by incorrect
handling or non-compliance with the safety instructions. In such cases the warranty/guarantee
is void.
An exclamation mark in a triangle points out important instructions in the operating manual.
Please read through the operating instructions completely before operating the device. They
contain important information for correct operation.
• Prior to commissioning, check the device for damage. If the device is damaged, do not put it into
operation.
• The unauthorized conversion and/or modification of the product is inadmissible because of safety
and approval reasons.
• The device may only be used with the 12V DC vehicle power supply (with the negative terminal of
the battery connected to the body of the vehicle). Never connect the device to any other power
supply.
• Make sure you use the device properly. Please also follow these operating instructions.
• Consult an expert when in doubt as to the operation, the safety or the connection of the device.
• Check the device and the connection leads for damages from time to time. An expert must repair
the product in case the device or the connection cables are damaged.
• Avoid heavy mechanical stress on the laminator and do not expose it to strong vibration or dripping
or spray water.
• Never pour out liquids above the device. You run the risk of causing a fire or a fatal electric shock. If
any liquid should nevertheless penetrate the device, immediately disconnect it from the power
supply network and contact a specialist.
• The device does not belong in the hands of children. Keep it away from children.
• Do not leave packaging material lying around carelessly. It may become a dangerous toy for
children.
• If you are not sure about the correct connection or if there are any questions that are not covered
by the operating instructions, do not hesitate to contact our technical support or another specialist.
• Observe the additional safety instructions in each individual section of these instructions.
Installation
The general safety instructions and regulations must be heeded by all means when performing
mounting works in, around and under the vehicle. Also observe the safety instructions of the
vehicle manufacturer!
Modifications to the vehicle which are made necessary through the installation of the device
must always be carried out in such a manner that neither the traffic safety nor the designed
stability of the car is impaired. If you are in doubt when selecting a place for installation,
consult your car dealer.
Make sure before drilling the holes that no electric cables, brake cables or similar can be
damaged.
When using tools for mounting your device, observe the safety instructions of the
manufacturer.
When installing the device, take into consideration the risk of accident which can arise from
devices being torn away in case of an accident. Therefore, you should secure every component
in a place where it cannot be dangerous to passengers.
Installation of the Instrument
The device can be attached to the dashboard with the enclosed installation angle or installed in a corresponding opening
in the dashboard.
Matching mounting and installation casings with a standard opening for installation instruments are available in retail stores
(partially also vehicle-specific).
• Select an appropriate installation location. The installation location must be
well visible from the driver's seat.
• When selecting the installation site, consider the required installation depth.
Especially ensure sufficient distance to moving vehicle parts (rods, levers,
etc.).
• Twist the attachment ring off the instrument and pull it out of the installation
angle.
• If applicable, attach the installation angle with 2 suitable screws on the
dashboard.
• Put the instrument into the installation opening and attach it by screwing the
attachment ring back on and tightening it by hand.
Installation of the Sensor
w w w. c o n r a d . c o m
w w w. c o n r a d . c o m
The enclosed sensor is screwed in at the engine (instead of the present oil pressure sensor).
Optional adapter screws are available if the thread on the engine does not match the thread of the enclosed sensor.
Ask your car dealer about a suitable installation site and the matching thread size prior to the installation.
Version 07/10
• Drain the engine oil from the oil tub if applicable.
• Remove the present oil pressure sensor.
• Screw the enclosed sensor into the thread on the engine (if applicable in connection with an adapter screw). Do not
use excess force here, otherwise you may damage the thread. Make sure to reinsert or replace any sealing rings.
• Check the tightness of the screw connection once you have completed the installation work by starting the engine
and letting it run for a while. No oil may emerge at the sensor.
Change of the Illumination Colour/Illuminant Change
• Pull the illuminant fitting from the rear of the inline instrument
• Push on one of the included coloured caps onto the illumination bulb.
• To change the bulb, pull it from the illumination fitting and insert a new one.
• Insert the fitting into the in-line instrument again.
Connection
• Disconnect the negative pole of the on-board battery.
• Connect the connection marked with (W W W W W ) on the
instrument with the vehicle earth or an earth lead
(clamp 31).
• Connect the connection marked with (+) on the
instrument with the 12V ignition plus (clamp 15). This
is a cable that carries 12V when the ignition is turned
on.
• Connect the white cable of the inline instrument
illumination to the power supply for the dashboard
light (clamp 58).
• Connect the black cable on the inline instrument illumination to the vehicle earth or an earth lead (clamp 31).
• Connect the sensor connection (S) on the instrument with the connection contact (S) of the previously installed
sensor on the engine.
• Connect the connection W.L/G. on the oil pressure sensor to the lead of the oil pressure warning lamp of the vehicle
that was previously connected to the oil sensor.
• Check the correct connection once again and then reattach the negative pole of the on-board battery.
• Check whether the instrument and the illumination work.
Maintenance and Care
The outside of the product should be cleaned with a clean dry cloth or brush only.
Never use any aggressive cleaning agents or chemical solutions that may damage the surface of the housing.
Disposal
Technical Data
Supply voltage: ....................................................................................... 12V=
Measuring range: ................................................................................... 0-7 bar
Lamp ....................................................................................................... Car glass socket bulb 12V/1,7W / W2,1x9,5d
Illumination colours: ............................................................................... White/red/green
Installation diameter: .............................................................................. 52mm
the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. These
operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2010 by Conrad Electronic SE.
The electric connection should be made by a specialist.
To avoid shorts and any resulting damage to the device, the negative terminal (earth) of the car
battery has to be disconnected first.
Only connect the negative pole of the battery, when you have completely connected the system
and checked the connections.
The contacts and cables of the on-board net to which the instrument is connected must be
secured with a corresponding fuse!
You should only use a voltmeter or a diode test lamp for checking the voltage on the on-board
cables as normal test lamps consume excessive currents and can thus damage the electronic
system of the car.
When installing the cables, make sure that these are not squashed or scrape on sharp edges!
Use cable nozzles for passage points.
Only use suitable car cables for connection. Bell wires etc. are not suited for installation in
cars.
You may also only use suitable car plug-type connections that must be installed with suitable
tools on the cables.
Try to install the connection leads along the car's cable tree and avoid loose cable loops that
may become caught in the pedals of the vehicle. This may lead to life-threatening situations
while driving.
At the end of its service life, dispose of the product according to the relevant statutory regulations.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-
92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
Publicité
