VXI VoxStar UC Guide De Démarrage Rapide

VXi VoxStar
Quick-Start Guide
Package Contents
1. BT2 Bluetooth ® USB
Adapter
2. VoxStar™ UC Headset
with Ear Hook
3. Cheek Pad
4. Foam Ear Cushions
(1 small and 1 large)
5. Rubber Ear Cushion
*Not to scale. **Not pictured.
IMPORTANT SAFETY NOTE: Prolonged exposure to high volume levels can damage your hearing. To avoid injury, set the volume to the lowest comfortable level.
If you experience ringing in your ears, or voices sound muffled, stop using the headset. Avoid turning up the volume to block noisy surroundings. It's possible
for your ears to adapt to volume that is too high, and this could result in permanent hearing damage without any noticeable discomfort.
Wearing style
To get the best performance from our noise-canceling technology, position the microphone near the corner of your mouth. Positioning is important; small adjustments
in microphone placement can improve performance.
The VXi VoxStar UC offers three wearing styles to ensure optimal fit and comfort: earhook, headband and neck band. To attach the headset to the wearing style of
your choice, please refer to the following photos.
Ear Hook
Optional cheek pad goes here
Charging
Connect charger cord into the headset's charging port. The headset LED will illuminate red when charging and blue when fully charged.
Turning headset on/off
Turn Headset On: Hold down the MFB for approximately 2-3 seconds until you hear a voice prompt, "Power on." The blue light will flash twice every second.
Turn Headset Off: Hold down the MFB for approximately 3-4 seconds until you hear a voice prompt, "Power off." A red light will flash 4 times and the headset
will turn off.
Placing Headset into Pairing Mode
With VoxStar UC powered off, press the MFB until the light rapidly flashes blue and you hear the audio prompt "Power On." Keep holding the MFB for
approximately 10 seconds until you hear "Discovering." Headset will be visible for pairing to devices for 120 seconds.
Pairing with the BT2 USB Adapter
Your VoxStar headset is pre-paired with the BT2 USB Adapter. If you wish to pair the BT2 to a different headset, follow these steps:
1) Place the headset into pairing mode.
2) Insert the BT2 into a USB port on the computer
3) The adapter will initialize and enter pairing mode while the computer installs driver files. The BT2 LED will flash quickly. The headset should connect with the
adapter either during initialization or shortly after. Note: If the adapter and headset do not pair the first time, unplug the adapter and repeat this procedure.
4) Make sure your PC's sound settings have the VXi BT2 USB Adapter as the default microphone and/or speaker. Go to www.vxicorp.com/usb for more information
on configuring your specific operating system
Pairing to a Cell Phone
1) Make sure that other Bluetooth devices are turned off or out of range.
2) Place VoxStar into pairing mode.
3) Put your cellphone in Bluetooth Search/Scan Mode per the manufacturer's instructions.
4) Select "VXi VoxStar" to pair. (Passcode is "0000" if needed.)
5) When connected, VoxStar will give you the voice prompt, "Your headset is connected."
Quick-Reference Tables
VoxStar UC Headset
Function
Power On
Power Off
Enable Pairing Mode
Volume Up
Volume Down
Mute (On/Off)
Answer a Call/Active Call
End a Call
Transfer Audio
Low Battery
BT2 Bluetooth USB Adapter LED Indicators
LED Light Sequence Function
Steady on/off flash Adapter not connected to a headset
Long on/short off flash Adapter connected to a headset
Fast flash Adapter in pairing mode
Multiple Device Pairing and Advanced Features
The VXi VoxStar can pair with up to eight (8) devices. However, only one device may be connected to the headset at a time, unless the headset is in Multipoint
Mode. For more information on advanced features, please refer to the complete user guide, available online.
For the full user guide, technical notes, and available accessories, go to www.vxicorp.com.
271 Locust Street | Dover, NH 03820 | Toll Free: 800-742-8588 | Phone: 603-742-2888 | www.vxicorp.com
© 2013 VXi Corporation. APN 203431A 12/13
IMPORTANT: CHARGE HEADSET FULLY PRIOR TO FIRST USE
™
6. Headband*
7. Neckband*
8. Contoured Ear Buds
(1 small, 1 medium, and 1 large)
9. Ear Bud Adapter Ring
10. USB Charging Cable**
11. AC Adapter**
12. Quick-Start Guide**
Button/Duration of Press LED Indicator
MFB (2-3 seconds) Blue, double flash (1 second)
MFB (3-4 seconds) All LEDs turn off
MFB (5-15 seconds) Blue, rapid flash
Volume Up (quick press) NONE
Volume Down (quick press) NONE
Volume Up (2 seconds) NONE
MFB (quick press) Blue flash, once per second
MFB (quick press) Blue flash, every 4 seconds
Volume Down (1-2 seconds) NONE
n/a Red, fast flash
UC
A 3
E D
2
1
Headband or Neckband
Audio Indicator
Short tone
NONE
NONE
Single tone
Single tone
Single tone, reminder tone
every 10 seconds
Two rising tones
Two falling tones
NONE
Long, high tone @ 20 seconds
Features and Functions
A. Indicator Lights
B. Multifunction Button (MFB)
C. Flexible Microphone Boom
D. Volume Down
E. Volume Up/Mute
4 5
B C
9
8
Ear Bud Assembly
Voice Indicator
"Power on"
"Power off"
"Discovering"
NONE
NONE
NONE
NONE
"Call terminated"
NONE
"Battery low"
6
7