F.F. Group DSL 710 PLUS Notice Originale page 10

10 | English
per. Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and may
cause snagging, tearing of the disc, or kickback.
GENERAL
This tool should not be used by people under the
ƒ
age of 16 years.
This tool is not intended for use by children
ƒ
and persons with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge.
Ensure that children do not play with the tool.
ƒ
This tool is not suitable for wet sanding.
ƒ
Always disconnect plug from power source be-
ƒ
fore making any adjustment or changing any
accessory.
ACCESSORIES
FF GROUP can assure flawless functioning of the
ƒ
tool only when the correct accessories are used
which can be obtained from your FF GROUP dealer.
For mounting/using non-FF GROUP accessories
ƒ
observe the instructions of the manufacturer con-
cerned.
Handle and store accessories with care.
ƒ
OUTDOOR USE
Connect the tool via a fault current (FI) circuit
ƒ
breaker with a triggering current of 30 mA max-
imum.
BEFORE USE
Before using the tool for the first time, it is recom-
ƒ
mended to receive practical information.
Always check that the supply voltage is the same
ƒ
as the voltage indicated on the nameplate of the
tool (tools with a rating of 230V or 240V can also
be connected to a 220V supply).
Use suitable detectors to find hidden utility
ƒ
lines or call the local utility company for assis-
tance (contact with electric lines can lead to fire or
electrical shock; damaging a gas line can result in
an explosion; penetrating a water pipe will cause
property damage or an electrical shock).
Do not work materials containing asbestos (as-
ƒ
bestos is considered carcinogenic).
Dust from material such as paint containing lead,
ƒ
some wood species, minerals and metal may be
harmful (contact with or inhalation of the dust
may cause allergic reactions and/or respiratory
diseases to the operator or bystanders); wear a
dust mask and work with a dust extraction de-
vice when connectable.
Certain kinds of dust are classified as carcinogenic
ƒ
(such as oak and beech dust) especially in conjunc-
tion with additives for wood conditioning; wear a
dust mask and work with a dust extraction de-
vice when connectable.
Follow the dust-related national requirements for
ƒ
the materials you want to work with.
Do not clamp the tool in a vice.
ƒ
Use completely unrolled and safe extension cords.
ƒ
DURING USE
Do not touch the moving sanding disc.
ƒ
Do not continue to use worn, torn or heavily
ƒ
clogged sanding discs.
If the cord is damaged or cut through while work-
ƒ
ing, do not touch the cord, but immediately dis-
connect the plug.
Never use the tool when cord is damaged; have it
ƒ
replaced by a qualified person.
In case of electrical or mechanical malfunction,
ƒ
immediately switch off the tool and disconnect
the plug.
In case of current interruption or when the plug
ƒ
is accidentally pulled out, unlock the on/off switch
immediately in order to prevent uncontrolled re-
starting.
AFTER USE
After switching off the tool, never stop the ro-
ƒ
tation of the accessory by a lateral force applied
against it.
GUIDELINES FOR USING EXTENSION CORDS
Make sure your extension cord is in good condition.
f
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
Always replace a damaged extension cord or have
f
it repaired by a qualified person before using it.
Protect your extension cords from sharp objects,
f
excessive heat and damp/wet areas.
Use a separate electrical circuit for your tools. This
f
circuit should be protected with the appropriate
time-delayed fuse. Before connecting the motor to
the power line, make sure the switch is in the OFF
position and the electric voltage is rated the same
as the voltage stamped on the motor nameplate.
Running at a lower voltage will damage the motor.
PRODUCT SPECIFICATIONS
INTENDED USE
This tool is intended for dry sanding of plastered
walls and ceilings; it is particularly suitable for re-
moving paint coatings, adhesives and loose plaster.
Only use the tool when correctly and completely
assembled (be aware that FF GROUP cannot be hold
responsible for tool damage and/or personal injuries
resulting from the incorrect assembly of the tool).
Read this instruction manual carefully before use and
save it for future reference .
TECHNICAL DATA
Article Number
Model
Rated voltage
Frequency
Rated power input
No-load speed
Pad diameter
DSL 710 PLUS
43 281
DSL 710 PLUS
V 230-240
Hz 50
W 710
min 1.000-2.200
-1
mm 210