Unito Ace Water Systems ACE.BOIL Mode D'emploi page 11

GB
PRODUCT SAFETY PRECAUTIONS
Read this document before installing and operating this product. Users must be familiar with all the information and applicable
standards prior to installing and using this product. Save this manual for future reference and use.
Warning: Use caution when dealing with boiling water. Children should not touch the device. This product must not be cleaned and
!
maintained by children without supervision.
Caution!
After assembling the water system and before turning on the power, please hold the boiling water knob open till water ows out from faucet outlet.
Connect the power and turn the Power button to"On"position to start heating the water.
Ambient conditions requirements: Relative humidity: 25%~90%; Storage temperature: -20 C to 60 C(-4 F to 140 F); - Operation
Ÿ
o o
temperature: 4 C~50 C(39.2 F to 122 F).
Do not install the unit near heat sources or an open fire. The unit environment should be well-ventilated.
Ÿ
Inform people who are unfamiliar with the ACE.BOIL water system about safe use. Incorrect use might result in injury.
Ÿ
Consult a service technician if the ACE.BOIL water system does not operate normally when you have followed the instructions
Ÿ
in this manual.
The filter is optional and can be fitted to reduce water hardness, to filter the content of the water for hygiene reason and to
Ÿ
extend the product's lifespan. Filters can be ordered online at the website https://www.ace2o.com/en.
Filtration with a water softener is mandatory when water hardness exceeds 10 dH.
Ÿ
Do not attempt to repair this product yourself. Always call an ACE qualified service technician to carry out adjustments or
Ÿ
repairs.
Any power cord used must comply with local and national standards and used under guidance of an authorized technician.
Ÿ
The ACE.BOIL water system may only be installed in accordance with the instructions in this manual. Incorrect installation of the
Ÿ
unit might result in damage to property. Do not use any extension cables other than those supplied with the unit or supplied by
ACE Water Systems.
The power supply cord and On-Off Power button are used to connect and disconnect the unit from power. Make sure that the
Ÿ
socket outlet and knob are accessible after installation.
Overloaded AC outlets, extension cords, and broken plugs are extremely dangerous and might result in electrical shock or fire
Ÿ
hazard.
Call an authorized service technician for any replacements.
Ÿ
Hands must be dry when plugging the power cord in or out of the AC outlet to prevent electrical shock. Do not damage the
Ÿ
power cord by disassembling, bending, pulling or exposing it to heat as this may cause a fire or electric shock.
Make sure to completely insert the power plug into an AC outlet. Unsecure connections can cause fire.
Ÿ
Make sure that the power source is properly grounded. Do not use extension cables and adapters between boiler and power
Ÿ
source.
Unplug the unit whenever it is not in use for an extended period of time.
Ÿ
TECHNICAL SPECIFICATIONS
ACE.BOIL water system
Dispensing water types
Boiling water tank capacity
Heating-up time
Min./Max. mains pressure
System max. safety pressure
Max. hot water temperature
Operation
Power supply
Max. power consumption
Standby power consumption
Safety features
Tank Dimensions
Empty tank weight
Full tank weight
Flow rate
Max. water hardness
Note: In areas where water hardness exceeds 10° dH (German hardness), an ACE filter with water softener must be used.
o o
Boiling water, cold/hot tap water
4.4 Litres
o
15 minutes (from 25 C to 100 C)
2/5 bar (200/500 kPa)
8 bar (800 kPa)
o
100 C
Operation via mechanical control knob, handle
220V-240VAC 50/60Hz
1550 W
0.35 W
Maximum temperature fuse, Safety valve(with a cut-off, relief valve ,a built-in non-return valve)
219 x 366 x 279 mm (L x H x W)
4KG
8.4KG
2.5 L/min
o
10 dH
o
o
10
o o o o