Battery Charger; Operating Instructions - NSS Enterprises EForce Scrubber 26 Manuel De L'opérateur

See Figure 10. Normal Mode screen shown.
70 Mode indicator
71 Reset. Touch to reset all settings to selected
mode's defaults.
72 Water Flow Setting. Touch desired button:
76 Conservation
77 Normal
78 Maximum
73 Scrubbing down force setting, Touch desired but-
ton:
Conservation
Normal
Maximum
74 Scrub motor speed. Touch desired button:
Conservation/Quiet
Normal
75 Vacuum level. Touch desired button:
Conservation/Quiet
Normal
Hour Meter Screen
See Figure 11
80 Hours on both scrub motors displayed here.
81 Hours on left drive motor displayed here.
82 Hours on right drive motor displayed here.
83 Hours on vacuum motor displayed here.
84 Supervisor Settings button.
85 Drain Clean Water (Solution) Tank button. Touch
to turn on vacuum motor without operator in the seat.
Supervise Mode Code Entry Screen
Enter code 1911 to continue to the Supervisor screen.
Supervisor Mode Screen
This screen provides a means to disable certain ma-
chine functions to suit.
Green buttons are available in all cleaning modes.
Grey buttons are disabled in all cleaning modes.
Fast ground speed can be disabled by touching the
speed button until the Fast Disabled is displayed.

Battery Charger

When the machine is supplied with batteries installed,
the battery charger is set by the NSS factory for the
installed batteries.
WARNING-When replacing NSS supplied batteries, or
installing batteries purchased from another source, the
battery charger must be set to the correct curve and
charge current for the batteries being installed.
Do not throw the batteries into the regular waste.
WARNING-The battery charger must always be
set to 24V.
Verifying Battery Charger Settings
• Uncoil the battery charger power cord from the
storage compartment (#17 Figure 1).
• Lift open the Upper Body (#38 Figure 2).
• Locate the battery charger cover, notice it is clear
and the battery charger display is visible.
• Connect the battery charger power cord to an ap-
propriate wall outlet.
• Note the display on the battery charger as it cycles
through the displayed settings:
• SPE (general information).
• 000U (general information).
• 007 (general information).
• 24.0U (THIS IS CHARGING VOLTAGE, MUST
BE 24.0U).
30.0A (THIS IS CHARGING CURRENT, VAR-
•
IES BY CURVE SETTING, SEE CHART BE-
LOW).
• 000c (THIS IS THE CURVE NUMBER SET-
10
TING, SEE CHART BELOW FOR CORRECT
CURVE).
• Acd (THIS IS BATTERY TYPE, SEE CHART
BELOW)
• Actual battery voltage is displayed.
• Charging current output is displayed.
Battery Charger Curves
Curve Battery Type,
Number 20hr rate
0 Crown wet
>300ah
1 Generic curve
for wet lead
acid
2 Crown wet
200-300ah
3 Crown AGM
Batteries
4 Generic curve
for wet w/
float
5 Fullriver AGM
6 Discover AGM 30A for 300+ah 25A
WARNING - Do not use the charger if the set-
tings do not match the battery type and size installed
in the machine. CALL FOR SERVICE
Setting the Battery Charger
The battery charger settings must be changed by a
qualified technician.
See 9098306 Charger Setup leaflet (Technician Use
Only) for instructions.

Operating Instructions

See Controls section for description of machine
and control elements.
WARNING-To prevent unauthorized use of the
machine, always switch off the keyswitch and remove
the key when the machine is to be left unattended.
DO NOT PLACE WET RAGS INTO CORD STORAGE
COMPARTMENT FIGURE 1 #17
Squeegee Installation
See Figure 1 #27, #28, #39 & #40.
• Loosen Squeegee Knobs #28.
• Slide the Squeegee under the machine, behind the
scrub deck.
• Lift the squeegee up, and slide it backwards en-
gaging the slots on the squeegee bracket #40.
• Tighten the Squeegee Knobs #28 gently.
• Push the Squeegee Hose into the center hole of
the Squeegee.
Alternative Method
• Sit on the seat.
• Turn on the Keyswitch (Figure 1 #1)
• Acknowledge the warning screens, then touch
Vacuun Only Mode button (Figure 9 #43).
• Once the squeegee bracket has been lowered com-
pletely to the floor, TURN OFF THE KEYSWITCH.
• Dismount the machine, and walk to the right hand
side of the machine.
Req'd Charge Current
30A
30A for 300+ah 25A
for 200-300ah
25A
30A for 300+ah 25A
for 200-300ah
30A for 300+ah 25A
for 200-300ah
30A for 300+ah 25A
for 200-300ah
for 200-300ah