Napa 6-1052 Instructions page 2

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
This insTrucTion Manual conTains
iMporTanT safeTy inforMaTion.
read This insTrucTion
Manual carefully and
undersTand all
inforMaTion Before
operaTing This Tool.
• It is the responsibility of the owner
to make sure all personnel read this
manual prior to using the device. It
is also the responsibility of the device
owner to keep this manual intact and
in a convenient location for all to see
and read. If the manual or product
labels are lost or not legible, contact
(NAPA Professional Air Tools) for
replacements. If the operator is not
fluent in English, the product and
safety instructions shall be read and
discussed with the operator in the
operator's native language by the
purchaser/owner or his designee,
making sure that the operator
comprehends its contents.
• Always operate, inspect and maintain
this tool in accordance with American
National Standards Institute Safety
Code of Portable Air Tools (ANSI
B186.1) and any other applicable safety
codes and regulations.
• For safety, top
performance and
maximum durability of
parts, operate this tool
at 90 psig; 6.2 bar max
air pressure with 3/8" diameter air
supply hose.
• Always wear impact-
resistant eye and face
protection (users and
bystanders) when
operating or performing
maintenance on this tool.
• High sound levels can
cause permanent
hearing loss. Always use
hearing protection (users
and bystanders) as
recommended by your employer and
OSHA regulations while using this tool.
• Keep the tool in efficient operating
condition.
• Operators and maintenance personnel
must be physically able to handle the
bulk, weight and power of this tool.
• Air powered tools can
vibrate during use.
Extended exposure to
vibration, repetitive
motions, or uncomfortable
positions during use may be harmful to
please revieW all Warning insTrucTions prior To operaTion. save This Man u al for fuTure ref er ence.
6-1052
WARNING
your hands and arms. Discontinue use
of tool if discomfort, tingling, or pain
occurs. Seek medical advice before
resuming use.
• Compressed air can
cause severe injury.
Never direct air at
yourself or others.
Always turn off the
air supply, drain hose
of air pressure and
detach tool from air
supply before installing,
removing or adjusting
any part or accessory on
this tool, or before
performing any
maintenance on this
tool. Failure to do so could result in
injury. Whip hoses can cause serious
injury. Always check for and replace
any damaged, frayed or loose hoses
and fittings. Do not operate a damaged
or worn tool. Do not use quick-detach
couplings at tool. See instructions for
correct set-up.
• Slipping, tripping and/or
falling while operating
air tools can be a major
cause of serious injury or
death. Be aware of excess
hose left on the walking or work
surface.
• Keep body working stance balanced
and firm. Do not overreach when
operating the tool.
• Anticipate and be alert for sudden
changes in motion during use of any
power tool.
• Do not point or indulge in any
horseplay with this tool.
• Note direction of rotation BEFORE
operating this tool.
• Keep tool out of reach of children.
• Do not carry tool by the
hose. Protect the hose
from sharp objects and
heat.
• Tool shaft may continue to rotate
briefly after throttle is released. Avoid
direct contact with accessories during
and after use. Gloves will reduce the
risk of cuts or burns.
• Keep away from
rotating end of tool.
Do not wear jewelry or
loose clothing. Secure
long hair. Scalping can
occur if hair is not kept away from tool
and accessories. Choking can occur if
neckwear is not kept away from tool
2
and accessories.
• Correct bonded abrasive mounted
point grinding wheels, rotary files
and carbide burrs are necessary to
prevent injury from broken accessories.
Do not use chipped or cracked bonded
abrasive mounted point grinding
wheels, rotary files and carbide burrs.
Tighten the bonded abrasive mounted
point grinding wheels, rotary files and
carbide burrs on the collet to prevent
spin off when the Die Grinder is
turned off.
• Do not force tool beyond its rated
capacity.
• RPM of the accessory must
exceed tool RPM.
RPM RPM RPM
• Use accessories rated
at 20,000 RPM or higher.
• Never mount a grinding wheel, cut-off
wheel, router cutter or drill bit on a
Die Grinder.
• Never use an arbor, mandrel or any
other adapter to convert the Die
Grinder for any other application.
• Do not lock, tape or wire
the "on/off" safety lever in
the "on" position, as the
lever must be free to return
to the "off" position when
released.
• This tool is not insulated
against electric shock.
• This tool must not be used
in explosive atmospheres.
• Do not lubricate tools with
flammable or volatile liquids
such as kerosene, diesel or
jet fuel.
• Do not remove any labels.
Replace damaged labels.
• Use replacement parts and accessories
recommended by NAPA Professional
Air Tools.
• Servicing and repairs should only be
made by an authorized service center.
• Do not use (or modify) the tool for
any other purpose than that for
which it was designed without
consulting the manufacturer's
authorized representative.
• Handling the brass parts of this product
will expose you to lead, a chemical
known to the State of California
to cause birth defects and other
reproductive harm. Wash hands
thoroughly after handling.
Rev. 9/9/14