Satco NUVO S38939 Mode D'emploi

LED TEMPORARY HIGH BAY
Models: S38939, S38944, S38946, S38960, S38974, S38975
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING:
• Please read this manual carefully before use, make sure the
application is in accordance with the instructions before use.
• To reduce the risk of electric shock and fire, do not exceed string
maximum wattage including any additional string loads. Maximum
number of connection lamps: 60W – 10PCS, 100W – 6PCS,
150W – 4PCS.
• Suitable for dry and damp locations.
• Disconnect the power to avoid shock when the equipment is wet.
• This device is not intended for use with emergency exits.
• This lamp should be not installed in heat or sealed environments or
near corrosive gases, so as not to affect the service life.
• Do not override any ignition of explosive materials on the surface,
so as not to cause a fire.
• This lamp must be installed, tested and maintained by professionals
using special equipment.
• Please check the product carefully after opening the package. If product
is damaged, please keep the packaging and contact the local dealer.
INSTALLATION INSTRUCTIONS
• Turn off power before installation.
• For one product, follow installation
steps: 1, 2 and 3.
• For two or more products, follow
installation steps: 1, 2, 3 and 4.
• Close the Cap of the last lamp,
when no other lamp connections
are needed.
• Turn on power.
Max number of ganged lamps
and fuse reset
The maximum number of lamps is
determined by the chart above.
Exceeding the maximum number
of fixtures could open the fuse.
To reset the fuse in the case of an
overload, unplug the extra lamps
for a minimum of 10 seconds.
Then reconnect the plugs and
turn the lamps back on.
© Copyright 2020 Satco Products, Inc. 3/20
PRODUCT FEATURES AND SPECIFICATIONS
The new generation LED Temporary High Bay is a work light with multi-
functions. It's designed with handle and lamp pads which can be used as
portable lights, and the hook structure of the lamp is very convenient to be
used for hoisting. The metal mesh cover design can protect from collision
and fall, and it's safer to use as a protective cover. The lamp is designed
in IP64, which can be used in a dry or damp environment. The plug and
socket can connect two or more lamps together, and the anti-pull metal
buckle on the lamps can make the lamp connection firm. The lamp has
a large luminous angle and high power which is suitable for installation in
open work spaces.
100W
150W
Figure 1
STEP 1
Hang on secure fixed
wall or object by the
base hook
STEP 4
Connect the plug and socket to make sure two or more lamps are joined together,
and rotate the Buckle 120˚ to make sure the lamp connection is firm.
Light
Watt Input Lamp Dimension
Effect
5.12" x 5.12" x 9.17"
60W 120V 100Im/W
(130 x 130 x 233mm)
5.12" x 5.12" x 10.94"
120V 100Im/W
(130 x 130 x 278mm)
5.12" x 5.12" x 12.13"
120V 100Im/W
(130 x 130 x 308mm)
NOTE: Total 5A max
in parallel connection
STEP 2
Ensure the fixed wall
or object is strong
enough to hold 66 lbs
120˚
Buckle
Max # of
Wire Lamp Operating
Lamp
Length Base Temperature
Connections
-22° to +113°F
6 FT HOOK 10PCS
(-30˚C to 45˚C)
-22° to +113°F
6 FT HOOK 6PCS
(-30˚C to 45˚C)
-22° to +113°F
6 FT HOOK 4PCS
(-30˚C to 45˚C)
STEP 3
Cap
Plug in and TURN ON
the power (AC 120V)
Close the Cap when no other
lamp connections are needed.
Cap
Satco Products, Inc.
Brentwood, NY 11717