Black & Decker KX3300 Traduction Des Instructions Initiales page 6

ENGLISH
Electrical safety
This product must be earthed. Always check that
the power supply corresponds to the voltage on
the rating plate.
Power plugs must match the outlet. Never modify the plug in
any way. Unmodified plugs and matching outlets will reduce
the risk of electric shock.
Extension cables & class 1 product
A 3 core cable must be used as your appliance is earthed
u
and of class 1 construction.
Features
1. Boiler carrying handle
2. Pressure relief valve
3. Boiler reservoir
4. Water level indication
5. Hose
6. Steam plate
7. Filler cap
Assembly
Fitting the hose (fig. A and B)
Screw one end of the hose (5) to the hose connector on
u
the boiler tank. Check that the hose has been connected
properly.
Connect the other end of the hose (5) to the steam plate.
u
Check that the hose has been connected properly.
Use
Surfaces may become hot in use. The filler cap
may be hot during use and during the cool down
period.
Initial filling of the boiler reservoir (fig. C)
Warning! Make sure that the appliance is unplugged.
Unscrew and remove the filler cap (7).
u
Note: When filling the boiler, use clean tap water only.
Fill the boiler reservoir (3) with water. Do not overfill the
u
reservoir past the MAX indicator (maximum 4 litres).
Replace the boiler filler cap (7), do not overtighten.
u
Plug the mains plug into the power supply.
u
Reaching temperature (fig. D)
Depending upon the temperature of the water used to fill
u
the reservoir (3), the appliance will take between 6 and 11
minutes to start producing steam.
6
(Original instructions)
Refilling the boiler reservoir
Disconnect the appliance from the mains supply.
u
Wait at least 2 minutes for the water to cool and the pres-
u
sure to decrease before removing the boiler filler cap (7).
Warning! The filler cap may be hot during use and during the
cool down period.
Unscrew and remove the filler cap (7).
u
Fill the boiler reservoir (3) with clean tap water. Do not
u
overfill the reservoir past the MAX indicator (maximum 4
litres).
Replace the boiler filler cap (7), do not overtighten.
u
Plug the mains plug into the power supply.
u
Using the wallpaper stripper (fig. E)
Check the state of your plaster before you start work
u
as high temperature steam can loosen weak, porous or
poorly bonded plaster. Plaster is also loosened more read-
ily in areas of cracks, holes or if the steam plate is held in
one position for too long.
You may be able to detect if you have weak plaster by
u
tapping a few areas of the walls with your knuckles. If this
produces a hollow sound, we recommend proceeding only
with extreme care.
In all cases test out the wallpaper stripper on a small area,
u
about 100 cm2 , before starting work properly.
If at any stage finishing plaster is loosened or you hear a
u
crack, do not continue. The wallpaper stripper is safe for
drywall/plaster board surfaces.
Due to the heat generated by this product, it is possible
u
that certain surfaces, ie. carpets, soft furniture, table tops,
cabinets etc., could be marked or damaged. To prevent
this, ensure a wooden board or other barrier is placed
under the boiler to prevent the heat damaging the surface.
Dust sheets or newspapers are not adequate for this
purpose.
For best results, remove wallpaper with a scraper. Scrape
u
off wallpaper in a downward direction (fig. F).
Always wear protection when removing wallpaper from the
u
ceiling. Be careful of condensation collecting in the steam
plate as hot water may drip (fig. G and H). Empty the
steam plate regularly and never use directly above your
head.
Always place the steam plate in a suitable container when
u
left unattended, even for a few seconds, and keep the
steam plate facing away from you when in use (fig. I and
J).
Storage
Allow the appliance to cool for at least 10 minutes.
u
Empty the appliance.
u
Store the appliance upright in a dry place.
u