Table des Matières
Publicité
Liens rapides
Publicité
Table des Matières
Manuels Connexes pour Flo Home X5
Sommaire des Matières pour Flo Home X5
- Page 1 Home X5 Model Installation guide...
-
Page 3: Table Des Matières
Table of Contents Safety Instructions Before You Install Box Contents Installing the Station Installing the PLC Checking the PLC Connection Connect the Station to your Account Light Indicators Sound Indicator Installating a Second Station Compliance Limited Warranty Assistance Charging Station Serial Number Casing: 100% aluminum NEMA 4X Certified, designed for outdoor or indoor installation Voltage: 208 - 240 V @ 60 Hz... -
Page 4: Safety Instructions
This charging station is to be used to charge vehicles that do not require a ventilated environment during charging. Always disconnect the power supply of the charging station before servicing. September 2018 | flo.com | Installation guide | FLO Home X5... - Page 5 Recommended height to facilitate handling of the connector, as well as preventing the cable from touching the ground. 7,6 in 6,9 in 19,3 cm 17,5 cm 17 in 43,2 cm 60 in 152,4 cm Floor FLO Home X5 | Installation guide | flo.com | September 2018...
-
Page 6: Before You Install
Maximum output power: 7.2 kW @ 240 V or 6.2 kW @ 208 V Figure 1 Single-Phase 120/240 VAC Charging Station Ground Ground Figure 2 3-Phase 120/208 VAC Charging Station Ground September 2018 | flo.com | Installation guide | FLO Home X5... -
Page 7: Installing The Station
The power supply cable can be inserted from the rear (a) or from under (b) the station: - 3/4 knockout (a) and (b) - Remove a single cap - Strain relief not included FLO Home X5 | Installation guide | flo.com | September 2018... - Page 8 Secure the rear housing of the station to the mount- ing plate. Screw the lower screw to secure the mounting. September 2018 | flo.com | Installation guide | FLO Home X5...
- Page 9 B) Tighten the 2 front screws with a nominal torque of 55 lbs-in. Detail A About 30° Switch on the electrical circuit breaker. Your new station can now charge your vehicle! FLO Home X5 | Installation guide | flo.com | September 2018...
-
Page 10: Installing The Plc
In case there are two or more electric panels in your home, ensure the PLC and the FLO Home X5 are on the same wiring and connected on the same electric panel, otherwise the PLC will not connect to the network. -
Page 11: Checking The Plc Connection
- SOLID : The Ethernet port is connected to your router. 3 Ethernet LED - OFF : There is no Ethernet connection. *PLC : Power-line communication technology enables you to build a computer network on your home’s electrical network. FLO Home X5 | Installation guide | flo.com | September 2018... -
Page 12: Connect The Station To Your Account
If you have not already done so, you can create your FLO account. Go to https://flo.ca/signup and follow the instructions. Log in to your FLO account. https://flo.ca/login September 2018 | flo.com | Installation guide | FLO Home X5... - Page 13 Enter the 16-character association code on the included card with your new station and click “Associate”. A message confirming the association should appear. Otherwise, contact our technical support for assistance. FLO Home X5 | Installation guide | flo.com | September 2018...
-
Page 14: Light Indicators
(only at start-up for White - Solid color (not blinking): the station is connected to the FLO server and the white light guides the insertion of the connector - Blinking slowly: the station cannot connect to the FLO... -
Page 15: Sound Indicator
- 2 long beeps: major fault requiring a power interruption (please restart the station by cutting the power at the circuit breaker in the electrical panel for 10 seconds, then restore power) FLO Home X5 | Installation guide | flo.com | September 2018... -
Page 16: Installating A Second Station
Installation of a Second Station Two FLO Home™ X5 can be connected to a separate or on the same 40A circuit breaker via a junction . The first charging station will automatically detect the second. - Power splitting only works with the FLO Home™ X5. -
Page 17: Compliance
- CSA C22.2 No. 0.8-12 Safety functions incorporating electronic technology. - UL1998 Standard for software in programmable components. - UL991 Standard for Tests for Safety-Related Controls Employing Solid-State Devices. - NEC 2014 section 625. FLO Home X5 | Installation guide | flo.com | September 2018... -
Page 18: Limited Warranty
Product. 4.Limited Remedies. FLO’s obligations under this Limited Product Warranty are limited to repairing or replacing or reimbursing the purchase price, at FLO’s sole discretion, any Product which is found to be defective by FLO after proper inspection. All replacement or repaired Products are warranted only for the remainder of the original Warranty Period, prolonged only by the period during which the Product was repaired or replaced. -
Page 19: Assistance
A customer experience or technical support representative can assist you! Customer and Technical Support For any questions regarding charging station installation, configuration or any technical problem. 1-855-543-8356 You can also contact us at: service@flo.com FLO Home X5 | Installation guide | flo.com | September 2018... -
Page 20: Charging Station Serial Number
Volt: 208 / 240 VAC 60Hz Courant max: 30A Amp: 30A max Boîtier / Enclosure: Type 4x Date Code: 201611 Operating Temp: -40 C to 50 FLO Home charging station bottom view September 2018 | flo.com | Installation guide | FLO Home X5... - Page 21 2 Hold your smart phone at a 20 angle under the charging station. 3 Line up the phone screen with the serial number sticker 4 When you see the sticker take the picture. FLO Home X5 | Installation guide | flo.com | September 2018...
- Page 22 THIS PAGE IS INTENTIONALLY LEFT BLANK...