Safety Information; Specifications - Thermolec DCC-9-BOX Manuel D'installation Rapide

SAFETY INFORMATION

This document describes important safety instructions which must be
followed during installation, maintenance and application of the DCC –
Charge controller for electric vehicles.
Warning
Read all instructions prior using this pro-
duct.
Always disconnect the DCC – Charge
controller for electric vehicles power sup-
ply before any works.
Use only the DCC – Charge controller for
electric vehicles by following the technical
specifications indicated in this installation
manual.
Do not install the DCC – Charge controller
for electric vehicles nearby inflammable
materials, explosives or fuels, chemical
products and vapors.
Never spray the DCC – Charge controller
for electric vehicles with water or any other
liquids.
Stop using the DCC – Charge controller for
electric vehicles immediately if defective,
cracked, broken or damaged.
Never try to modify, repair or dismantle the
DCC – Charge controller for electric vehi-
cles. Please contact the manufacturer for
any malfunction.
Never insert a sharp object inside the DCC
– Charge controller for electric vehicles at
the risk of causing damages to the com-
ponents.
Any improper use of the DCC – Charge
controller for electric vehicles could result
in serious injuries which may cause death.
For a vertical installation on a wall, refer to
the information's on the enclosure for the
choice of mounting position.
Precautions
Any improper use of the DCC – Charge
controller for electric vehicles can cause
damages and premature wear of the com-
ponents, which voids the warranty.
Never use the DCC – Charge controller for
electric vehicles above or below the tem-
perature range of -22 °F to 113 °F (-30 °C
to 45 °C).
Only store the DCC – Charge controller for
electric vehicles above or below the tem-
perature range of -4 °F to 158 °F (-20 °C
to 70 °C).
The installation of the DCC – Charge
controller for electric vehicles must be
done in accordance with the latest electri-
cal code requirements.
Notes
It is recommended to schedule the char-
ging of the vehicle during hours of low
electrical consumption to minimize inter-
ruptions to the electric charging station.
Always check that the DCC – Charge
controller for electric vehicles is adequa-
tely fixed to the wall or ceiling or in a loca-
tion to avoid any damages.
It is the installer's responsibility to make
sure that the electric power source is
adequate for the use of the DCC – Charge
controller for electric vehicles.
Do not use any cleaning solvents to clean
the DCC – Charge controller for electric
vehicles.
Limited warranty
1 - THERMOLEC LTÉE. warrants the inte-
grated controls against any defects for a
period of one year from the shipping date.
The warranty is limited to the equipment
and components supplier by THERMOLEC
LTÉE.
2 – In case of incorrect installation, inap-
propriate use or repairs done by unautho-
rized personnel by THERMOLEC LTÉE., the
warranty will be automatically void.
3 - THERMOLEC LTÉE. undertakes to re-
pair or replace, at site or at the manufac-
turing location, at his option, the defective
material only after an evaluation made by
its representative.
4 - THERMOLEC LTÉE. will not be held
liable for damages or delays and will not be
required to pay transport cost of the charge
controller said to be defective.
5 - THERMOLEC LTÉE. shall not be liable
for any indirect damages or delays caused
by faulty workmanship or materials.
No indemnity will be paid for repairs, repla-
cements or modifications without a prior

SPECIFICATIONS

Models
DCC-9-BOX, manufactured by Thermolec, is a splitter box specifically
designed to make a building's electrical infrastructures fully ready for
DCC-9-BOX
electric vehicles at the lowest possible price.
DCC-9-BOX-3R
Voltage and wiring
Terminals size
Dimensions
12" x 12" x 7.5"
14" x 13" x 8"
NEMA 3R enclosure
*Approximative and can change without notice.
4
written consent supplied by THERMOLEC
LTÉE.
6 – Any control device or accessory sup-
plied with the DCC – Charge controller for
electric vehicles to be installed or connec-
ted remotely from the charge controller will
be guaranteed by the manufacturer only
under the special conditions mentioned in
paragraph 5.
7 – The components supplied for repairs
are guaranteed for the remaining of the
warranty on the original product or 90 days.
The longest period will prevail.
8 – All repairs made at the THERMOLEC
LTÉE. plant are guaranteed for 30 days
from the date of repairs.
Main power supply
60A 70A 80A 90A 100A 125A
240/208V AC single phase:
L1, L2, Neutral, Ground.
up to 2/0
(CU/AL)
Total weight
* *
(H" x W" x D")
11 lb (4,99 kg)
12 lb (5,44 kg)
V1