Thermolec DCC-9-BOX Manuel D'installation Rapide

Masquer les pouces Voir aussi pour DCC-9-BOX:

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

DCC-9-BOX
INSTALLATION MANUAL
MANUEL D'INSTALLATION
Nema 3R Enclosure
Boitier Nema 3R
MODELS
MODÈLES
DCC-9-BOX, DCC-9-BOX-3R
Demand charge controller
for electric vehicles
Contrôleur de charge pour véhicules électriques
1
I
MAIN POWER SUPPLY
120/240-208V, Single Phase
60A - 70A - 80A - 90A - 100A - 125A
ALIMENTATION PRINCIPALE
120/240-208V, Monophasé
60A - 70A - 80A - 90A - 100A - 125A
APPROVED MARKET
Amérique du Nord
Read and save these instructions
Lire et garder ces instructions
Manufactured by
Manufacturé par
Designed by
Design par
I
E N G L I S H
I
F R A N ÇA I S
I
North America
MARCHÉ AGRÉÉ
V7

Publicité

Table des Matières
loading

Sommaire des Matières pour Thermolec DCC-9-BOX

  • Page 1 60A - 70A - 80A - 90A - 100A - 125A APPROVED MARKET North America MARCHÉ AGRÉÉ Amérique du Nord Read and save these instructions Nema 3R Enclosure Boitier Nema 3R Lire et garder ces instructions Manufactured by MODELS MODÈLES Manufacturé par DCC-9-BOX, DCC-9-BOX-3R Designed by Design par...
  • Page 3: Table Des Matières

    THERMOLEC LTÉE. / RECHARGE VÉHICULE ÉLECTRIQUE and Characteristics its licensors. Additional information’s are available on request. The following logos are trade names or trademarks of THERMOLEC LTÉE. / Typical installation RECHARGE VÉHICULE ÉLECTRIQUE in the United States and in Canada.
  • Page 4: Safety Information

    Models Main power supply cal code requirements. materials, explosives or fuels, chemical DCC-9-BOX, manufactured by Thermolec, is a splitter box specifically products and vapors. 100A 125A Notes designed to make a building’s electrical infrastructures fully ready for Never spray the DCC –...
  • Page 5: Characteristics

    Installations types Group installation, Wall installation, Ceiling installation Main Power Supply (CB) DCC-9 with The DCC-9-BOX can be powered by a 240/208V AC single phase SUB PANEL source, max 125A. The following options are offered by each DCC model: Models...
  • Page 6: Maintenance

    STEP 2: PREPARATIONS FOR INSTALLATION Wall installation 1. Remove the 4 cover screws. 1. Disconnect the main power 2. Position the DCC at the intended location. 2. Select the DCC intended location. 3. Ensure that the mounting is according with the information’s The DCC can be mounted: on the enclosure.
  • Page 7 Ce manuel d’installation ne peut pas être modifié, reproduit ou copié, en tout ou en partie, sans l’autorisation écrite préalable de Caractéristiques THERMOLEC LTÉE. / RECHARGE VÉHICULE ÉLECTRIQUE et ses concé- dants de licence. Des informations supplémentaires sont disponibles sur Exemple d’installation demande.
  • Page 8: Information De Sécurité

    Ne jamais asperger le DCC - Contrôleur vigueur. Modèles Alimentation principale de charge pour véhicules électriques Le DCC-9-BOX de Thermolec est un boîtier de répartition spécia- d’eau ou de toutes autres liquides. Notes 100A 125A lement conçu pour préparer un immeuble à l’arrivée des véhicules Arrêtez d’utiliser immédiatement le DCC...
  • Page 9: Caractéristiques

    Types d’installations Installation groupée, installation au mur, installation au plafond Alimentation principale (CB) DCC-9 avec Le DCC-9-BOX peut-être alimenté par une distribution électrique SOUS PANNEAU monophasée 240/208V CA, max 125A. Voici les possibilités qu’offre chaque modèle de DCC: Modèles Alimentation principale...
  • Page 10: Maintenance

    ÉTAPE 2 : PRÉPARATION À L’INSTALLATION 6. Vérifier que le DCC est fixé adéquatement au mur ou au plafond. 7. Défaire le support d’installation pour le plafond. 1. Couper l’alimentation principale 2. Choisir l’emplacement du DCC Installation au mur 1. Enlever les 4 vis du couvercle. Le DCC peut s’installer: - sur un plafond 2.

Ce manuel est également adapté pour:

Dcc-9-box-3r

Table des Matières