General Safety Information; Tool Components And Specifications - Campbell Hausfeld SB303000 Mode D'emploi

Operating Instructions
General Safety
Information
(Continued)
an imminently hazardous situation
which, if not avoided, WILL result in
death or serious injury.
G Read and understand
tool labels and manual.
Failure to follow
warnings, dangers, and
cautions could result in
DEATH or SERIOUS INJURY.
G Do not use any type of
reactive gases,
including, but not
limited to, oxygen and
combustible gases, as
a power source. Use
filtered, lubricated, regulated
compressed air only. Use of a reactive
gas instead of compressed air may
cause the tool to explode which will
cause death or serious personal
injury.
G Use only a pressure-
regulated compressed
air source to limit the
air pressure supplied
to the tool. The
regulated pressure
must not exceed 100 psi. If the
regulator fails, the pressure
delivered to the tool must not
exceed 200 psi. The tool could
explode which will cause death or
serious personal injury.
G Never use gasoline or
other flammable
liquids to clean the
tool. Never use the
tool in the presence

Tool Components And Specifications

• REQUIRES: 0.3 SCFM with 10
fasteners per minute @ 90 psi
• AIR INLET: 1/4 inch NPT
• FASTENER SIZE RANGE: 3/8 inch to
1-1/4 inch
• MAGAZINE CAPACITY:
100 fasteners per load, 18 gauge
• STAPLES: 1/4 inch crown
• WEIGHT: 2 lbs., 13 oz.
• LENGTH: 9 1/2 inches
• HEIGHT: 8 3/4 inches
• MAXIMUM PRESSURE: 100 psi
• PRESSURE RANGE: 60 - 100 psi
www.chpower.com
of flammable liquids or gases.
Vapors could ignite by a spark and
cause an explosion which will result
in death or serious personal injury.
Danger
G Always remain in
indicates
a firmly balanced
position when
using or handling
the tool.
G Do not remove,
tamper with, or
otherwise cause
the Work Contact
Element (WCE) or
trigger to become
inoperable. Do not operate any tool
which has been modified in a like
fashion. Death or serious personal
injury could result.
O
CO
2
G Do not touch the
trigger unless
driving fasteners.
Never attach air
line to tool or
carry tool while
touching the
trigger. The tool could eject a
fastener which will result in death
or serious personal injury.
100 psi
a potentially hazardous situation
MAX.
which, if not avoided, COULD result in
death or serious injury.
G Always
disconnect the
tool from the
power source
when
unattended,
performing any
maintenance or repair, clearing a
jam, or moving the tool to a new
Work contact
element (WCE)
G Always fit tool
G Never place hands or
Warning
G Never carry the
indicates
Cap exhaust
Trigger
Adjustable depth
control
Fastener discharge area
2
Model SB303000
location. Always reconnect the air
line BEFORE loading any fasteners.
Do not load the tool with fasteners
when either the trigger is depressed
or the Work Contact Element (WCE)
is engaged. The tool could eject a
fastener causing death or serious
personal injury.
with a fitting
or hose
coupling on or
near the tool in
such a manner
that all compressed air in the tool is
discharged at the time the fitting or
hose coupling is disconnected. Do
not use a check valve or any other
fitting which allows air to remain in
the tool. Death or serious personal
injury could occur.
any other body parts in
the fastener discharge
area of the tool. The
tool might eject a
fastener and could
result in death or serious personal
injury.
tool by the air
hose or pull the
hose to move the
tool or a
compressor. Keep
hoses away from heat, oil and sharp
edges. Replace any hose that is
damaged, weak or worn. Personal
injury or tool damage could occur.
Warning label
Magazine
Latch
button