Installing The Ear Speaker And Microphone; Connecting Ear Speaker And Microphone To; Interphone Headset; Getting Started - Cellularline BTEASY Manuel D'utilisation

BTEASY

3. installing the ear speaker and microphone

Now you need to attach the ear speaker and micro-
phone arm to the inside of the helmet . Take the velcro
which the ear speaker will attach to, and test for the best
position to fix it . The velcro should be fixed at the height
of your ear . You will need to put the helmet on a few
times to find the optimum position . When the correct
positioning is found, remove the protective strip and
apply the velcro .
Next, take the ear speaker and attach it to the velcro .
Run the microphone arm down along down to where
your mouth will be . As the microphone arm is flexible,
you can adjust it so it sits in the optimum position in
front of your mouth .
note: There are two types of velcro, thin and thick .
Please use based on the actual situation .
4. Connecting the ear speaker and microphone to

interphone headset

Take care to connect USB cable to the USB port of inter-
phone headset, now you have successfully installed the
interphone .
18

- getting started

1. Charging the interphone headset

The Bluetooth® interphones have built-in rechargeable
batteries, prior to using them, it is recommendable to
charge their batteries fully for the first time .
Connect one end of USB cable to a standard power out-
let and the USB plug to the USB port of the interphone
headset . The red LED will be on while charging . It takes
about 2 hours to charge the battery fully . When charg-
ing has completed, the red LED will be off .
When the Bluetooth® interphone is on and the battery
becomes low, the red LED flashes and the Bluetooth®
interphone emits 3 "DU" tones every 30 seconds . Please
recharge the battery fully as described above .
notes:
1) When you can't turn off the Bluetooth® interphone,
you can turn it off as soon as you charge it .
2) There is USB charging cable .
Warning:
1) The battery is recyclable .
2) Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat place such as sunshine,
fire or the like .

2. turning on/off BteasY

indication
function operation led indicator
tone
Power on Press and Blue LED is on 1 long tone
hold mfB for 1 second
button for 3 and then flashes
seconds twice
Power off Press and Red LED is on 1 long tone
hold mfB for 1 second
button for and then flashes
7-8 seconds twice
Entering Press and Red and blue 2 short tones
pairing mode hold mfB LEDs flash
button for alternately
3-5 seconds
note: If you want BTEASY to enter pairing mode, you
have to press and hold mfB button for 3-5 seconds
when the interphone is turned off or in standby mode .
3. Pairing BteasY with a Bluetooth® device
Pairing with a Bluetooth® cell phone
You have to pair BTEASY Bluetooth® interphone with a
Bluetooth® cell phone before first use . Please make sure
your cell phone is Bluetooth®-enabled . Specific pairing
steps may vary with different models of cell phones .
Please refer to your cell phone's user's manual for further
information . The general pairing steps are as follows:
1) Keep BTEASY and Bluetooth® cell phone within 1
meter when pairing;
2) Ensure BTEASY is turned off, otherwise turn off
BTEASY first;
3) Press and hold mfB button for about 3-5 seconds, the
red and blue LEDs will flash alternately . BTEASY now
entered pairing mode;
4) Turn on your cell phone's Bluetooth® function to search
for Bluetooth® devices . After the search is completed,
select "BTEASY" from the Bluetooth® device list;
BTEASY
5) According to the indication, enter password or PIN
No:"1234", and press "Yes" or "confirm";
6) After successful pairing, select "BTEASY" from the
Bluetooth® device list, and press "connect" . The indica-
tor light of BTEASY will flash twice every 4 seconds if
connected successfully .
Pairing two interphones together
If you want to use the Bluetooth® intercom feature, you
have to pair two interphone together first . The general
pairing steps are as follows:
1) Keep two interphones within 1 meter when pairing;
2) Make one of interphones enter pairing mode;
3) Press and hold mfB button of another interphone
until blue LED is on;
4) The interphone whose blue LED is on will auto-
matically search and connect the interphone which
entered pairing mode . After successfully connecting,
the blue LEDs of both interphones will flash twice
every 4 seconds .
IT
EN
FR
ES
DE