SEKUR SFERA Serie Mode D'emploi page 14

1. General information
D.P.I. s.r.l. has carefully worded and edited this instruction manual. However, in no event shall D.P.I. s.r.l. be
liable for any damage caused by misunderstandings of the text, misprints or incompleteness. SEKUR is a
registered trademark of the personal protective equipment manufactured by D.P.I. s.r.l.. Technical alterations
of this equipment are not allowed.
1.1 Before using SEKUR SFERA masks, users must ensure that all Instructions in this manual are read,
understood and followed.
1.2 SEKUR masks have been specifically designed for the use described in this manual.
1.3 Repair and replacement of spare parts must be carried out by trained personnel, using original SEKUR
spare parts.
1.4 It is advisable for all periodic mask testing to be carried out by D.P.I. s.r.l. technical service or by other
trained personnel qualified for this purpose, according to the instructions of the appropriate
paragraph.
1.5 The D.P.I. s.r.l. standard warranty indicates the full extent of the liability of D.P.I. s.r.l.. D.P.I. s.r.l. will
not accept liability for any damages caused by:
a) testing which has not been carried out;
b) testing and maintenance improperly carried out by persons other than those qualified to do so by
D.P.I. s.r.l.;
c) improper usage of the mask.
1.6 D.P.I. s.r.l. will not accept liability for any damages caused by failure to abide by the aforementioned
provisions.
1.7 For everything which has not been mentioned above, the general conditions of this warranty apply. In
the event that you don't know the conditions of the contract, D.P.I. s.r.l. will send further information
upon written request.
1.8 The products Declaration of Conformity is available on the web site www.dpisekur.com in the specific
section.
2. Applicable standards, field of application, cautions and warnings
SFERA masks are PPE belonging to the III category according to the EU Regulation 2016/425, and they
conform to the requirements specified in the EN 136:98 Norm; they are equipped with standard threaded
connector according to the Norms EN 148-1 and EN 148-3 (see table). Testing according to the relevant
Norms, certification and authorisation to CE marking have been performed by the following Notified Bodies:
SFERA
SFERA SP/A
SFERA SP/A ESA
SFERA SP/A ESA SIL
SFERA SP/A ATEX
SFERA SP/A ATEX SIL
SFERA SIL
SFERA SP/A ASB
SFERA SP/A ASB SIL
The CE marking "CE 0426" on the mask facepiece indicates the Notified Body carrying out the production
control in accordance with the procedure foreseen in Annex VIII (D Module) of the EU Regulation 2016/425 -
Italcert - Viale Sarca, 336 - 20126 Milano - Italy (Notified Body n. 0426).
Full face mask with negative or positive pressure, are personal protective device for breathing protection,
that combined respectively with filters or respirators, provide breathable air to the user.
The instructions for use of filters and respiratory equipment, as well as the safety standards and regulations
issued by the competent authority, must be strictly followed. Respiratory protective devices must be used by
personnel in good health and trained in the use of this kind of equipment. Users must be beardless and
without sideboards or moustaches as these interfere with the facepiece seal, thus impeding adequate seal
(4333.3005)
(4333.3004)
(4333.2026)
(4333.2024)
(4201.0659)
(4201.0660)
(4333.3002)
(4344.2066)
(4344.2067)
DEKRA EXAM (ex DTM)
Essen - Germany
(Notified Body n. 0158)
Italcert - Viale Sarca, 336
20126 Milano – Italy
(Notified Body n. 0426)
14