Cleaning And Maintenance - ulsonix TOPCLEAN 1100A Manuel D'utilisation

EN
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there is
still a slight risk of accident or injury when using the
device. Stay alert and use common sense when using
the device.
3. USE GUIDELINES
The device is designed for wet cleaning, waxing and
polishing concrete, epoxy, tiled floors, etc. This machine is
intended for commercial use, for example in hotels, schools,
hospitals, factories, shops, offices and rental businesses.
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
1
7
2
2
8
3
4
9
5
6
7
10
12
11
13
14
15
16
1. Safety lock switch
2. Start button
3. Handle tilt adjustment lever
4. Water distribution adjustment lever
5. The chain connecting the adjustment lever
with the tank
6. Main power cord
7. Tank mounting bracket
8. An opening to top up water in the tank
9. Water tank
10. Water release valve
11. Engine power cord
12. Engine cover
13. Housing
14. Caster
15. Base
16. Damper ring
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher than
40°C and the relative humidity should be less than 85%.
Ensure good ventilation in the room in which the device
is being used. There should be at least 10 cm distance
between each side of the device and the wall or other
objects. The device should always be used when positioned
on an even, stable, clean, fireproof and dry surface, and
be out of the reach of children and persons with limited
mental and sensory functions. Position the device such that
you always have access to the power plug.
10
The power cord connected to the appliance must be
properly grounded and correspond to the technical details
on the product label.
Disassemble the device and all its components and clean
them before the first use.
ASSEMBLING THE APPLIANCE
1. Carefully unpack all components of the device.
2. Place the bottom part of the device with casters on
the floor.
3. Unscrew the screws marked in the drawing below,
place the handle control unit so that the assembly
holes in the unit correspond to the holes in the
device.
4. Replacing the screws, screw the unit to the device.
5. Connect the plug fitted to the handle control unit to
the socket in the bottom part of the device.
6. Fit the water tank onto the pipe of the scrubbing
disc, gently pushing it into the mounting brackets.
Make sure that it has been properly attached every
time before refiling the tank.
7. Connect the chain connecting the adjustment lever
to the tank
8. Connect the water hose with the water distribution
valve and the connector in the bottom part of the
device.
13.03.2019
9. In order to attach the scrubbing disc, tilt the
scrubber. Place the scrubbing disc onto the handle
control unit and turn it counter clockwise until you
feel resistance.
3.3. DEVICE USE
3.3.1. OPERATION
PLEASE NOTE: Hold the handles firmly when starting the
engine and while the engine is working.
1. Fill the tank with water and, if needed, with an
appropriate cleaning agent.
2. Connect the power cord to the power source.
3. To change the device holder tilt relative to the
ground, press the tilt adjustment handle.
4. Slide one of the safety lock buttons towards the
centre of the control handles.
5. Press and hold both start buttons to start the engine.
Releasing the buttons results in the engine shut
down.
6. To distribute water held in the tank, press the water
release valve handle.
7. If the water tank becomes empty while the scrubber
is working, turn the device off releasing the start
buttons, and refill the tank.
8. Turn the device off by turning all switches back to
the start position.
9. When you have finished work, position the handle
control unit vertically, and disconnect the device
from the power source. Drain the water tank. Please
note: remember to comply with detergent removal
legal requirement.
3.3.2. Hazards in the course of using the device
The hazards that can occur during use of the machine
are mechanical hazards. The mechanical hazard occurs
in situations in which injuries can result from mechanical
impact of various elements, e.g. machine parts, tools,
etc. on people. The basic mechanical hazards include
squeezing, crushing, cutting, pulling in or catching; impact;
puncture; abrasion; as well as slipping and stumbling.
These hazards can occur both during normal machine
operation and as a result of irregularities in machine
operation. These irregularities might result in machine
failure. The mechanical hazards can result from: moving
machines, transported loads, moving elements, sharp/
rough elements, dropping elements/loads, slippery uneven
surfaces, limited space, location of the work station in
relation to the ground.
3.3.3. INSPECTIONS AND PERIODIC CONTROL
Before being used, the new or repaired machine must
be checked by qualified technical personnel who have
knowledge and experience within the scope of operation
and maintenance of this type of machine. The machine
must be checked regularly by means of visual control of
the machine's condition, before, during and after use.
13.03.2019
11 EN
The check must be performed by the machine's operators.
Any irregularities in machine operation as well as any
damage must be reported to the proper technical personnel.
Do not use the machine if damage or any irregularities in its
operation were found.
NOTE: Disconnect the machine from the power supply
before each inspection.
• PRELIMINARY INSPECTION: Before first use. All new
or repaired machines must be checked by a qualified
and competent person to ensure the machine meets
the requirements of this operating manual.
• DAILY CHECK
brush wear check
»
control buttons efficiency check
»
handle control unit mounting check
»
• PERIODIC CHECK
water system gaskets wear and tightness check
»
moving elements fasteners check
»

3.4. CLEANING AND MAINTENANCE

a) Unplug the mains plug and allow the device to cool
completely before each cleaning, adjustment or
replacement of accessories, or if the device is not
being used. Wait for the rotating elements to stop.
b) Use only non-corrosive cleaners to clean the surface.
c) After cleaning the device, all parts should be dried
completely before using it again.
d) Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
e) Do not spray the device with a water jet or submerge
it in water..
f) Do not allow water to get inside the device through
vents in the housing of the device.
g) Clean the vents with a brush and compressed air.
h) The device must be regularly inspected to check its
technical efficiency and spot any damage.
i) Do not leave the battery in the device if it will not be
used for a longer period of time.
j) Use a soft, damp cloth for cleaning.