Samsung 6 Serie Mode D'emploi page 28

Masquer les pouces Voir aussi pour 6 Serie:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Advanced Features
how to set up automatically
To set up the wireless connection automatically, follow these
steps:
1. Follow Steps 1 through 6 in the "How to set up using
PBC(WPS)". (P. 27)
2. Press the ▼ button to select Internet Protocol setup,
and then press the EnTERE button.
Press the ▲ or ▼ button to select Auto, and then press
the EnTERE button.
3. Press the ▲ button to go to select a network, and
then press the EnTERE button. The network function
searches for available wireless networks. When done, it
displays a list of the available networks.
4. In the list of networks, press the ▲ or ▼ button to select
a network, and then press the EnTERE button.
If the AP is set to Hidden (Invisible), you have
to select Add network and enter the correct
network name (ssID) and security Key to
establish the connection.
5. If the Security/PIN pop-up appears, go to Step 6. If the
Network Connecting Screen appears, go to Step 10.
6. Press the ▲ or ▼ button to select security or PIn. For
most home networks, you would select Security (for
security Key). The security Screen appears.
Select a network
Security Key
A
B
C
D
E
H
I
J
K
L
O
P
Q
R
S
V
W
X
Y
Z
7. On the security screen, enter your network's Pass
Phrase.
You should be able to find the Pass Phrase on
one of the set up screens you used to set up your
router or modem.
8. To enter the Pass Phrase, follow these general
directions:
Press the number buttons on your remote to enter
numbers.
Use the direction buttons on your remote to move
from button to button on the security Key screen.
Press the Red button to change case or display
symbols/characters.
To a enter letter or symbol, move to the letter or
symbol, and then press the EnTERE button.
To delete the last letter or number you entered,
press the Green button on your remote.
28
English
0 entered
Number
0~9
F
G
M
N
Lower case
T
U
Delete
B
Space
C
n Move E Enter R Return
9. When done, press the Blue button on your remote. The
Network Connecting screen appears.
10. Wait until the connection confirmation message is
displayed, and then press the EnTERE button. The
network setup screen re-appears.
11. To test the connection, press the
select network Test, and then press the EnTERE
button.
network setup (Ad-hoc)
You can connect to a mobile device without an access point
through the "Samsung Wireless LAN Adapter" by using a
peer to peer network.
how to connect to new Ad-hoc
1. Follow Steps 1 through 6 in the "How to set up using
PBC(WPS)". (P. 27)
2. Choose select a network. A list of devices/networks
appears.
3. While in the device list, press the Blue button on the
remote.
The message
"Ad-hoc is a direct WI-Fi
connection with cellphone or PC. The existing
network system may have limited functionality.
Do you want to change the network
connection?" is displayed.
4. Input the generated network name (ssID) and
security Key into the device you want to connect.
how to connect an existing Ad-hoc device
1. Follow Steps 1 through 6 in the "How to set up using
PBC(WPS)". (P. 27)
2. Choose select a network. Then, the device list will be
displayed.
3. Select the device you want in the Device list.
4. If security key was applied, input the security key.
If network does not operate normally, check
the network name (ssID) and security Key
again. An incorrect security Key may cause a
malfunction.
RETURn
button to

Publicité

Chapitres

Table des Matières
loading

Table des Matières