Portability Kit Installation - Coleman Powermate PMC606750 Mode D'emploi

PORTABILITY KIT INSTALLATION

TOOLS REQUIRED: 1/2" and 9/16" sockets and ratchets,
block(s) of wood (minimum of 6" tall). Refer to the parts list
on page 9.
WHEEL INSTALLATION
1. Block up end of generator opposite the fuel tank cap to
install wheel kit.
2. Insert wheel spacer (item 39) into the center of the wheel
(item 28).
3. Slide 3/8 x 4.25" bolt (item 32) and 3/8 washer (item 27)
through the wheel (item 28), then through the wheel
bracket on the carrier, with the offset side of the wheel hub
against the wheel bracket.
4. Thread 3/8 nyloc nut (item 33) onto the bolt and tighten to
securely clamp the wheel assembly to the carrier.
5. Repeat above instructions for the remaining wheel.
FOOT INSTALLATION
1. Blocking up the engine side of the generator, place the foot
bracket (item 43) under the carrier channel. Thread a
5/16-18 x 4" bolt (item 42) with a rubber foot (item 29)
through the mounting holes and thread a 5/16 flange nut
(item 47) to the bolt to secure the foot bracket to the carrier.
Caution: Do not over tighten so that the rubber foot
material collapses.
LOCKING HANDLE
1. Attach the lanyards (item 30) to the release pins (item 34)
and carrier as shown in the illustration.
2. To lock the handle (item 25) in the extended position, align
the holes in the handle brackets with the holes in the carrier
brackets and insert the release pins (item 34).
1
30
English
2
34
LIMITED WARRANTY
Warranty Coverage: Powermate Corporation (the Company)
warrants to the original retail customer in North America that it
will repair or replace, free of charge, any parts found by the
Company or its authorized service representative to be
defective in material or workmanship. This warranty covers the
cost of replacement parts and labor for defects in material or
workmanship.
Not Covered:
· Transportation charges for sending the product to the
Company or its authorized service representative for
warranty service, or for shipping repaired or replacement
products back to the customer; these charges must be
borne by the customer.
· Damages caused by abuse or accident, and the effects of
corrosion, erosion and normal wear and tear.
· Warranty is voided if the customer fails to install, maintain
and operate the product in accordance with the instructions
and recommendations of the Company set forth in the
owner's manual.
· The Company will not pay for repairs or adjustments to the
product, or for any costs or labor, performed without the
Company's prior authorization.
Warranty Period: Two (2) years from the date of purchase on
products used solely for consumer applications; if a product is
used for business or commercial applications, the warranty
period will be limited to one (1) year from the date of purchase;
if a product is used for rental applications, the warranty period
will be limited to ninety (90) days from the date of purchase.
For warranty service, the customer must provide dated proof of
purchase and must notify the Company within the warranty
period.
For warranty service: Call toll free 800-445-1805, or write
to Powermate Corporation, Product Services, 4970 Airport
Road, P. O. Box 6001, Kearney, NE 68848.
EXCLUSIONS AND LIMITATIONS: THE COMPANY MAKES
NO OTHER WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED. IMPLIED WARRANTIES, INCLUDING
WARRANTIES OF MERCHANTABILITY AND OF FITNESS
FOR A PARTICULAR PURPOSE, ARE HEREBY
DISCLAIMED. THE WARRANTY SERVICE DESCRIBED
ABOVE IS THE EXCLUSIVE REMEDY UNDER THIS
WARRANTY; LIABILITY FOR INCIDENTAL AND
CONSEQUENTIAL DAMAGES IS EXCLUDED TO THE
EXTENT PERMITTED BY LAW.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. Some states
do not allow a disclaimer of implied warranties, or the exclusion
or limitation of incidental and consequential damages, so the
above disclaimers and exclusions may not apply to you.
3