Technical Data - Car-O-Liner CMI 3000 II Guide De L'utilisateur

Technical data

POWER SOURCE
Mains voltage ±15% (50-60Hz), V
- Autotransformer optional ±15% (50-60Hz), V
Minimum generator size, kVA
Fuse, A
Mains current, effective, A
Mains current, max., A
Power, 100%, kVA
Power, max., kVA
Power, open circuit, VA
Efficiency, %
Power factor
Current range, A
Duty cycle, 100% 20°C (MIG), A
Duty cycle, max. 20°C (MIG), A/%
Duty cycle, 100% 40°C (MIG), A/V
Duty cycle, max. 40°C (MIG), A/%/V
Open circuit voltage, V
Sphere of application
1)
Protection class
2)
Wire feed speed, m/min
Torch connection
Wire-reel diameter, mm
Wire diameter, mm
Gas pressure, MPa (bar)
Standards
Dimensions (HxWxL), mm
Weight, kg
FUNCTION
Selection of trigger mode, 2-times / 4-times
Control of current/voltage/ wire feed speed
Wire inching
Hot-start %
Hot-start-time, sec.
Arc power, %
Gas pre-flow, sec.
Soft-start, m/min
Hot-start, %
Hot-start-time, sec.
Slope down time, sec.
Stop Amp, A
Stop Amp time, sec.
Burn back
Gas post-flow, sec
Sequence timer / Spot welding time, sec.
DUO Plus™ efficiency, %
DUO Plus™ time, sec.
Electronic choke
Sequence, Sequencesteps
1) S This machine meets the demand made for machines which are to operate in areas with increased hazard of electric chocks.
2) Equipment marked IP23 is designed for indoor and outdoor applications.
CMI 3000 II
3x400
3x230-500
18.5
16
16.5(380V)/15.7 (400V)
19.0 (380V)/18.1 (400V)
10.9
12.5
40
85
0.90
15-300
300
300/100
270/30.8
300/80/32.0
69-76
S/CE
IP23
0.5-30.0
EURO
300
0.6-2.4
0.6 (6.0)
EN/IEC60974-1.
EN/IEC60974-5.
EN/IEC60974-10
906x524x925
58
PROCESS VALUE RANGE
MIG/MAG 2/4
- local/torch control/remote control
MIG/MAG yes
MMA 0.0-100.0
MMA 0.0-20.0
MMA 0.0-150.0
MIG/MAG 0.0-10.0
MIG/MAG 0.5-24.0
Synergic -99 - +99
Synergic 0.0-20.0
Synergic 0.0-10.0
Synergic 0-100
Synergic 0.0-10.0
MIG/MAG 0-30
MIG/MAG 0.0-20.0
MIG/MAG 0.0-50.0
MIG/MAG 0-50
MIG/MAG 0.1-9.9
-5.0 - +5.0
9
hereby declare that our machine as stated below
Type: CMI 3000 II
conforms to directives: 2014/35/EU
European standards:
Regulation:
Issued in Västra Frölunda 10.02.2021
18
EC DECLARATION OF CONFORMITY
Alignment Systems AB
Hulda Mellgrens gata 1
SE-421 32 Västra Frölunda
SWEDEN
2014/30/EU
2011/65/EU
EN IEC60974-1:2018/A1:2019
EN IEC60974-5:2019
EN / IEC60974-10:2014/A1:2015
2019/1784/EU
Morgan Ekskär
Quality Manager