WORLD DRYER AirStyle DB Serie Mode D'emploi page 3

Installation
IMPORTANT: Consult local and general regulations before performing dryer installation. Make certain that the electrical
network is not overloaded. Do not connect to a branch circuit with a circuit breaker or fuse rated over 20 Amps. This is a UL
recommendation and complies with NEC.
A) DISCONNECT THE POWER SOURCE.
B) Surface Mounted Models
1) Use the security Allen wrench supplied to remove the (2) cover mounting screws. Remove
the cover from the dryer.
2) Place the hand dryer base on the wall at the desired location using Table 1 to determine
the recommended mounting height. With the base so located, use it as a template to mark
locations of the 4 mounting bolt holes on the wall. When two or more dryers are installed,
they should be spaced 24" (61 cm) minimum from center to center.
3) Fasten the base to the wall, using the type of bolts suggested in Table 2.
4) Connect the dryer to the nearest suitable distribution panel.
5) Replace cover, making certain not to over-tighten cover bolts.
Type of Wall
Hollow Tile, Lath, Wall Board or Metal
Cement, Brick, or Tile Covered Cement or Brick
Stud Wall with Wood Backing
C) Recessed Mounted Models
1) Mount the hand dryer wall box at the recommended height per Table #1.
3) Caulking is recommended AFTER installation of the aluminum base
D) Mounting the Steel Wall Box;
CAUTION: Proper installation requires that the base be installed into the steel wall box supplied.
1) Locate the steel wall box in the wall at the desired position, having the lower edge of the box at the selected height spec
2) When two or more dryers are installed, they should be spaced 24" (61cm) minimum from center to center.
3) To mount the wall box, frame the opening in the wall per Figure #1.
4) Allow an opening in the framing to correspond with the preferred wall box knock-out for easy access of electrical conduit.
5) Mount the wall box in the opening. Fasten with No.10 (M5) wood screws or appropriate fasteners as required.
6) Using the nearest suitable distribution panel, run conduit.
8) Provide a minimum length of 24" (61cm) of wire in the wall box to allow easy connection to the dryer terminals.
E) Mounting the Dryer in the Wall Box;
1) Remove all shipping / packing material including the protective rubber corner squares if present on the dryer cover.
2) Use the security allen wrench supplied, to remove the (2) cover mounting screws. Remove the cover from the dryer base assembly.
CAUTION: should be exercised when handling porcelain enameled cast iron covers. Do not drop or hit against hard surfaces to
avoid damaging the porcelain enamel.
3) Insert the base assembly in the pre-mounted wall box.
4) Facing the dryer, the blower housing will be on the left side as installed.
5) Fasten the base to the wall box with (4) 1/4-20 screws supplied.
6) Route the wires through the openings in
the base assembly.
to the ground screw point.
DANGER: This hand dryer must be
properly earth connected (grounded).
any moving parts or sharp edges.
9) Install the Hand Dryer Cover with the (2)
mounting screws. To avoid chipping the
porcelain enamel, do not over-tighten.
INSTALLATION MUST BE PERFORMED
BY QUALIFIED ELECTRICIAN.
Table 1
Table 2
Type of Bolt
1/4" (M6) Screw Type or Wing Type Toggle Bolts
1/4" (M6) Stud Type Expansion Bolts
No.16 (M8) Wood Screws
em.)
EDGE FLUSH
TO RECESS
1/8" MAX.
1 1/4"
3 1/2"
12 1/2"
OPENING
8 KNOCKOUTS
#16 GA.
STEEL BOX
DIMENSION "A"
SECTION "A" SEE TABLE
3
Recommended Mounting Heights from
Floor to Dryer Bottom Edge
Men's washrooms
Women's washrooms
Children's washrooms, ages 4-7
Children's washrooms, ages 7-10
Children's washrooms, ages 10-13
Children's washrooms, ages 13-17
Handicap Mounting Height
Figure
1
3"
3"
7/8" + 1 1/8"
3"
1 1/4"
1 1/4"
3"
in. (cm.)
68 (173)
59 (150)
41 (104)
48 (122)
54 (137)
59 (150)
55 (140)
Minimum Bolt Length
Dependent on wall thickness
3" (76 mm)
23/4" (70 mm)
A
3"
1 1/4"
1 1/4"
3"
8 HOLES FOR #10
WOOD SCREWS
3"
3"
11 3/4"
OPENING
A