Preventative Maintenance; Service And Repair - Vollrath Instacut 55457 Manuel De L'opérateur

PREVENTATIVE MAINTENANCE

1. Use for the intended purposes only.
2. Inspect the equipment before each use. Do not use this equipment with missing, broken or worn components.
3. Clean the equipment after every use.
REPLACE THE BLADE ASSEMBLY
WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts. To avoid injury from
sharp blades, handle with caution.
1. Wash the blade assembly with warm, soapy water. Rinse thoroughly
to remove the thin protective oil film.
2. Sliding the T-handle assembly off the guide rods.
3. Raise the bumpers approximately 2" (5.0 cm).
4. Remove the old blade assembly by loosing the thumbscrew and
then carefully pressing upward on the underside of the frame that
surrounds the blades.
NOTICE: Do NOT touch the sharp understand of the blades.
TROUBLESHOOTING
Problem
Broken Blade
Pusher head does not slide easily.
Cuts poorly.
Cannot push food through.

SERVICE AND REPAIR

Serviceable parts are available on Vollrath.com.
To avoid serious injury or damage, never attempt to repair the unit or replace a damaged power cord yourself. Do not send units directly to
The Vollrath Company LLC. Please contact Vollrath Technical Services for instructions.
When contacting Vollrath Technical Services, please be ready with the item number, model number (if applicable), serial number, and proof of
purchase showing the date the unit was purchased.
WARRANTY STATEMENT FOR THE VOLLRATH CO. L.L.C.
This warranty does not apply to products purchased for personal, family or household use, and The Vollrath Company LLC does not offer a written
warranty to purchasers for such uses.
The Vollrath Company LLC warrants the products it manufactures or distributes against defects in materials and workmanship as specifically
described in our full warranty statement. In all cases, the warranty runs from the date of the end user's original purchase date found on the receipt.
Any damages from improper use, abuse, modification or damage resulting from improper packaging during return shipment for warranty repair will
not be covered under warranty.
For complete warranty information, product registration and new product announcement, visit www.vollrath.com.
The Vollrath Company, L.L.C. Headquarters
1236 North 18th Street
Sheboygan, Wisconsin
53081-3201 USA
Main Tel: 800-624-2051 or 920-457-4851
Main Fax: 800-752-5620 or 920-459-6573
Canada Customer Service: 800-695-8560
Tech Services: techservicereps@vollrathco.com
www.vollrath.com
Might be Caused By
Blades were dull.
Guide rods improperly or
insufficiently lubricated.
Blades are dull.
Blades are misaligned or incorrect
pusher block is installed.
Pujadas
Ctra. de Castanyet,
132 P.O. Box 121
17430 Santa Coloma de Farners
(Girona) – Spain
Tel. +34 972 84 32 01
info@pujadas.es
5. Install the new blade assembly by inserting the tab on the frame that
surrounds the blades into the groove in the base. Then lower the
blade assembly into a seated and flush position in the base. Tighten
the thumbscrew.
6. Slide the bumpers down the guide rods so they rest on the base.
7. Position T-handle assembly onto the guide rods and slowly lower
the assembly. Check the pusher head block to blade assembly
alignment.
8. Lubricate the guide rod with mineral oil, Petrol-Gel or other food-
grade lubricant after each use.
NOTICE: Do NOT use cooking oil as it will become sticky and may
permanently damage the equipment.
Course of Action
Replace the blade assembly. Also inspect the pusher block. Replace if
damaged.
Clean and lubricate the guide rides. See Cleaning.
Replace blade assembly.
Confirm the pusher block is correct for the blade assembly and that there
is no interference between the pusher block and blade assembly.
Vollrath of China
Vollrath Shanghai Trading Limited
Room 201, Building A
Xin Yi Plaza
1618 Yi Shan Road
Shanghai, 201103
China, P.R.C.
Tel: +86-21-5058-9580
©
2019 The Vollrath Company L.L.C.
Vollrath de Mexico S. de R.L. de C.V.
Periferico Sur No. 7980 Edificio 4-E
Col. Santa Maria Tequepexpan
45600 Tlaquepaque, Jalisco | Mexico
Tel: (52) 333-133-6767
Tel: (52) 333-133-6769
Fax: (52) 333-133-6768
Part No. 351753-1 ml 1/30/19