Operating The Stapler - Campbell Hausfeld SN258K Instructions D'utilisation

Operating Instructions
General Safety
Information
(Continued)
labels are located on the tool maga-
zine and body.
Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown, exam-
ine the tool closely for bent, cracked
or broken parts and air leaks. STOP
and repair before using or serious
injury could occur.
Caution indicates
CAUTION
!
a potentially haz-
ardous situation which, if not avoided,
MAY result in minor or moderate
injury.
Do not make any modifications to the
tool without first obtaining written
approval from Campbell Hausfeld. Do
not use the tool if any shields or
guards are removed or altered. Do
not use the tool as a hammer.
Personal injury or tool
damage may occur.
Always check
that the Work
Contact Element
(WCE) is operat-
ing properly. A
fastener could
accidentally be
driven if the
WCE is not
working properly. Personal injury
may occur (See "Checking the Work
Contact Element" Section).
Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
tools can be ejected from the front
of the tool. Personal injury may
occur.
Recommended Hookup
NOTICE
mation, that if not followed, MAY
cause damage to equipment.
Avoid using the tool when the mag-
azine is empty. Accelerated wear on
the tool may occur.
Clean and check all air supply hoses
and fittings before connecting the
tool to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
Air compressors providing air to the
tool should follow the requirements
established by the American
National Standards Institute
Standard B19.3-1991; Safety
Standard for Compressors for
Process Industries. Contact your air
compressor manufacturer for
information.
Operating The
Stapler
Read this manual and understand
all safety warnings and instruc-
tions before operating the stapler.
LUBRICATION
This stapler requires lubrication before
using the stapler for the first time and
before each use. If an inline oiler is
used, manual lubrication through the
air inlet is not required on a daily basis.
NOTICE
aged by excessive lubrication. Proper
lubrication is the owner's responsibility.
Failure to lubricate the stapler properly
will dramatically shorten the life of the
stapler and void your warranty.
1. Disconnect the
air supply from
the stapler to
add lubricant.
2. Turn the sta-
pler so the air
inlet is facing up. Place 4-5 drops of
Quick
Quick
Coupler
Plug
Air
Hose
Notice indicates
important infor-
3. After adding oil,
RECOMMENDED HOOKUP
The illustration below shows the
recommended hookup for the stapler.
1. The air com-
2. An oiler can be used
3. Use 3/8" air
The work surface
can become dam-
4. Use a pressure regulator on the
Regulator
Quick Plug
(Optional)
Oiler
Quick
Coupler
(Optional)
3
Model SN258K
30 W non-deter-
gent oil into air
OIL OIL
inlet. Do not use
detergent oils, oil
additives, or air tool
oils. Air tool oils
contain solvents
which will damage
the stapler's internal components.
run stapler briefly.
Wipe off any
excess oil from the
cap exhaust.
pressor must be
able to main-
tain a mini-
mum of 50 psi
when the sta-
pler is being
used. An inadequate air supply can
cause a loss of power and inconsis-
tent driving.
to provide oil circu-
lation through the
stapler. A filter can
be used to remove
liquid and solid
impurities which
can rust or "gum up" internal parts of
the stapler.
hoses with a
150 psi WP
minimum
3/8" I.D.
working pres-
sure of 150
psi. Use 1/2"
air hoses for 50' run or longer. For
better performance, install a 3/8"
quick plug (1/4" NPT threads) with
an inside diameter of .315" (8mm)
on the stapler and a 3/8" quick cou-
pler on the air hose.
compressor, with an operating pres-
sure of 0 - 125 psi. A pressure regu-
Filter
www.chpower.com
50 psi
Min.
100 psi
Max.