Vector Welding MIG Serie Mode D'emploi page 29

Summary
Description
MIG185
Weight 8kg
size(LxWxH)
391x153x282
Cooling Fan Cooled
Multi Process Inverter
Welder Type
Power Source
European Standards EN 60974-1 / IEC 60974-1
Mains voltage 1 x 230 Volt ±15%
Grid frequency
50/60Hz
Wire roll weight 5kg
Wire roll diameter 0.6/0.8/1.0
Efficiency 80%
Power Factor 0.8
Welding Current Range (MIG Mode)
30-185 A
Welding Current Range (STICK Mode)
30-160 A
Welding Current Range (WIG Mode)
10-180 A
Effective Input Current 18.9 A
Maximum Input Current
30A
Single Phase Generator Requirement 10KVA
185A@ 40%23V
Duty cycle, 40°C, 10 min(MIG)
114A@ 100%20V
160A@ 40%26V
Duty cycle, 40°C, 10 min(MMA)
101A@ 100%24V
180A@ 40%17.2V
Duty cycle, 40°C, 10 min(TIG)
114A@ 100%14.6V
Open Circuit Voltage
60V DC
Protection Class
IP23
Insulation Class H
NOTE
Note 1: The Effective Input Current should be used for the determination of cable size & supply
requirements.
Note 2: Generator Requirements at the Maximum Output Duty Cycle.
Note 3: Motor start fuses or thermal circuit breakers are recommended for this application. Check local
requirements for your situation in this regard.
Due to variations that can occur in manufactured products, claimed performance, voltages, ratings, all
capacities, measurements, dimensions and weights quoted are approximate only. Achievable capacities
and ratings in use and operation will depend upon correct installation, use, applications, maintenance
and service.
49
MIG SERIES EQUIPMENT
MIG205
8kg
391x153x282
Fan Cooled
Multi Process Inverter
Power Source
EN 60974-1 / IEC 60974-1
1 x 230 Volt ±15%
50/60Hz
5kg
0.6/0.8/1.0
80%
0.8
30-205 A
30-170 A
10-200 A
30 A
50.7A
10KVA
205A@ 35%24V
121A@ 100%20V
170A@ 35%26.8V
100A@ 100%24V
200A@ 35%18V
118A@ 100%14.7V
60V DC
IP23
H
MIG SERIES EQUIPMENT
Description
MIG225
Weight 8kg
size(LxWxH)
391x153x282
Cooling Fan Cooled
Multi Process Inverter
Welder Type
Power Source
European Standards EN 60974-1 / IEC 60974-1
Mains voltage 1 x 230 Volt ±15%
Grid frequency
50/60Hz
Wire roll weight 5kg
Wire roll diameter 0.6/0.8/1.0
Efficiency 80%
Power Factor 0.8
Welding Current Range (MIG Mode)
30-225 A
Welding Current Range (STICK Mode)
30-170 A
Welding Current Range (WIG Mode)
10-200 A
Effective Input Current 24.8 A
Maximum Input Current
41.9A
Single Phase Generator Requirement 10KVA
225A@ 35%25V
Duty cycle, 40°C, 10 min(MIG)
133A@ 100%21V
170A@ 35%26.8V
Duty cycle, 40°C, 10 min(MMA)
100A@ 100%24V
200A@ 35%18V
Duty cycle, 40°C, 10 min(TIG)
118A@ 100%14.7V
Open Circuit Voltage
60V DC
Protection Class
IP23
Insulation Class H
NOTE
Note 1: The Effective Input Current should be used for the determination of cable size & supply
requirements.
Note 2: Generator Requirements at the Maximum Output Duty Cycle.
Note 3: Motor start fuses or thermal circuit breakers are recommended for this application. Check local
requirements for your situation in this regard.
Due to variations that can occur in manufactured products, claimed performance, voltages, ratings, all
capacities, measurements, dimensions and weights quoted are approximate only. Achievable capacities
and ratings in use and operation will depend upon correct installation, use, applications, maintenance
and service.
Summary
MIG255
11.5kg
493x222x375
Fan Cooled
Multi Process Inverter
Power Source
EN 60974-1 / IEC 60974-1
1 x 230 Volt ±15%
50/60Hz
5kg/15kg
0.6/0.8/1.0
80%
0.8
30-255 A
30-170 A
10-200 A
30 A
50.7A
10KVA
255A@ 35%26.7V
151A@ 100%21.6V
170A@ 35%26.8V
100A@ 100%24V
200A@ 35%18V
118A@ 100%14.7V
60V DC
IP23
H
50