Symbols On The Unit - weinor BiSens SW-Solar Instructions De Montage

Masquer les pouces

Table Des Matières

Table des Matières

Les langues disponibles

Charging the BiSens SW-Solar

The BiSens SW-Solar is supplied discharged.

– Before using the BiSens SW-Solar for the first time, place it

under a lamp/in the sun for at least 30 minutes or press a travel

button for at least 1 minute to the 1st step only.

Note: The travel buttons have two steps.

The first step transfers energy from a built-in cell to the energy

store.

The second step runs the travel command.

Setting the mode (awning, visual protection, roller

shutter)

The BiSens SW-Solar can be operated in three different modes.

You can switch through the modes in sequence.

The current mode of the BiSens SW-Solar is indicated by the

transmission LED flashing.

When the system is supplied it is set by default to the awning

mode.

A different mode can also be preset in OEM versions.

Awning mode

(1 x flashing of the transmission LED)

The awning is automatically retracted when the current measured

light value changes from 1 to 0 (late evening) or when the current

measured light value changes from 0 to 1 (early morning).

Visual protection mode

(only with BiSens SW-230V,

2 x flashing of the transmission LED)

To keep the blind closed in the evening too, close the blind

manually using your hand-held transmitter or a timer.

The current transitions of the measured light values from 1 to 0

(late evening) or from 0 to 1 (early morning) will be ignored.

The blind will remain closed throughout the night.

The switching commands such as tilting position (venetian blind)

or ventilation position (roller shutter) will be executed automatically

the next day.

Roller shutter mode

(only with BiSens SW-230V, 3 x flashing of

the transmission LED).

If the roller shutter is operated manually or by a timer to the lower

end position, the light function (travel according to specified light

values) is switched off.

The current transitions of the measured light values from 1 to 0

(late evening) or from 0 to 1 (early morning) are ignored.

You can switch on the light function again in several different ways:

– a manual UP travel command (button on the

BiSens SW-Solar) moves the shutter to the upper end position.

– an automatic timer command moves the shutter to the upper end

position.

– by switching from AUTO mode to MANUAL mode and back to

AUTO mode.

2 | EN

Changing the mode

You will find the multi-way switch for setting the wind threshold value

on the underside of the BiSens SW-Solar.

1. Use a small screwdriver to set the multi-way switch to Function.

2. Press and hold the UP and DOWN buttons for at least 3 seconds.

Pressing the two buttons again switches to the next mode.

The current mode of the BiSens SW-Solar is indicated by the

Transmit LED flashing.

The operating mode is indicated by the flashing signal.

Transmission LED flashes 1x

Transmission LED flashes 2x

Transmission LED flashes 3x

The mode set is indicated at each radio transmission by the flashing

of the transmission LED (LED flashing pattern 1x every 3 minutes).

Set the multi-way switch back from Function to a wind value of your

choice.

Programming the BiSens SW-Solar

Condition:

1. Move the blind to aRoller n intermediate position.

2. Press and hold the UP, DOWN and P buttons on the programmed

hand-held transmitter for at least 3 seconds.

If the blind now travels UP and DOWN, continue at 4.

If the blind does not travel UP and DOWN, continue at 3.

3. Press and hold the STOP/P button on the BiSens SW-Solar for

3 seconds until the transmission LED begins flashing orange

rapidly. The blind now moves UP and DOWN for 2 minutes. The

transmission LED will flash orange rapidly every time a button is

pressed if the system is in programming mode.

4. Press the UP button on the unit immediately after the start of an

up movement (retract) bmodesegins. The drive will stop briefly.

5. Press the DOWN button on the unit immediately after the start of

a down movement (extend) begins. The drive will stop.

The BiSens SW-Solar is now programmed.