Work Area; Tool Components And Specifications - Campbell Hausfeld CHN10302 Mode D'emploi

Operating Instructions
Important Safety Instructions
(Continued)
GENERAL
a. To reduce the risks of
electric shock, fire, and
injury to persons, read all
the instructions before
using the tool.
b. Be thoroughly familiar with the
controls and the proper use of the
equipment. Follow all instructions.
Contact your Campbell Hausfeld
representative if you have any
questions.
c. Only persons well acquainted with
these rules of safe operation should
be allowed to use the unit.
Read and
understand tool
labels and manual. Failure to follow
warnings, dangers, and cautions could
result in DEATH or SERIOUS INJURY.

WORK AREA

a. Keep the work area clean and well
lighted. Cluttered benches and dark
areas increase the risks of electric
shock, fire, and injury to persons.
b. Do not operate the tool
in explosive atmospheres,
such as in the presence
of flammable liquids,
gases, or dust. The tool is
able to create sparks resulting in the
ignition of the dust or fumes.

Tool Components and Specifications

• REqUIRES: 0.3 SCFM with
10 nails per minute @ 90 psi
• AIR INLET: 1/4 inch NPT
• NAIL SIZE RANGE:
3/8 inch to 1-1/4 inch
• MAGAZINE CAPACITY:
100 Staples per load, 18 gauge
• WEIGHT: 2 lbs. 15 oz.
• LENGTH: 10-1/2 inches
• HEIGHT: 9-1/2 inches
• MAXIMUM PRESSURE:
100 psi
• PRESSURE RANGE:
60 psi – 100 psi
www.chpower.com
c. Keep bystanders, children, and
visitors away while operating the
tool. Distractions are able to result in
the loss of control of the tool.
PERSONAL SAFETY
a. Stay alert. Watch what you are
doing and use common sense
when operating the tool. Do not
use the tool while tired or under
the influence of drugs, alcohol,
or medication. A moment of
inattention while operating the
tool increases the risk of injury to
persons.
b. Dress properly. Do not wear loose
clothing or jewelry. Contain long
hair. Keep hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long
hair increases the risk of injury to
persons as a result of being caught
in moving parts.
c. Avoid unintentional starting.
Be sure the switch is off before
connecting to the air supply. Do not
carry the tool with your finger on
the switch or connect the tool to the
air supply with the switch on.
d. Do not overreach. Keep proper
footing and balance at all times.
Proper footing and balance enables
better control of the tool in
unexpected situations.
Work Contact
Element (WCE)
Fastener
Discharge
Area
2
CHN10302, CHN10310
e. Use safety equipment. A dust mask,
non-skid safety shoes and a hard
hat must be used for the applicable
conditions.
f. Always wear eye
protection.
g. Always wear hearing
protection when using
the tool. Prolonged
exposure to high intensity
noise is able to cause
hearing loss.
h. Do not attach the hose or tool to
your body. Attach the hose to the
structure to reduce the risk of loss of
balance if the hose shifts.
i. Always assume that the tool
contains fasteners. Do not point
the tool toward yourself or anyone
whether it contains fasteners or not.
j.
nail. This is able to cause the nail to
be deflected and hit someone, or
cause the tool to react and result in a
risk of injury to persons.
k.
when not driving fasteners. Never
carry the tool with finger on trigger,
the tool is able to fire a fastener.
position when using or handling the
tool.
with the tool. Stop using the tool if you
feel pain in hands or arms.
Quick Clear Nose
Magazine
Latch
Do not nail on
top of another
Remove finger
from the trigger
Always remain in a
firmly balanced
Avoid long extended
periods of work
Cap Exhaust
Trigger
Air
Inlet