Technical Data - Renkforce 1414578 Mode D'emploi

Partitioning/formatting a hard drive/SSD
A new HDD/SSD must be partitioned and formatted before it will appear in,
for example the Windows File Manager and before it can be used.
• In Windows, partitioning and formatting is easy to do via the control panel (via Com-
puter Management/Disk Management).
• After partitioning, the newly created partition has to be formatted. Fast formatting is
sufficient; "normal" formatting may take a long time to complete, depending on the
size of the HDD/SSD.
Handling
• If a has been installed, do not move the hard drive enclo-
hard drive with magnet discs
sure when it is in operation. Movement during operation may cause the write/read
heads in the hard drive to make contact with the magnetic disk. This may not only
lead to data loss but may also damage the hard drive!
The same applies to the 30-second period after the hard drive enclosure has been
switched off, until the magnetic disk in the hard drive has come to a full stop.
Naturally, this does not apply when using an SSD, since an SSD does not
have any moving parts.
• Protect valuable furniture surfaces by using a suitable mat to prevent scratches or
pressure points.
• Place the hard drive enclosure where it cannot fall down or topple over.
Cleaning
Before cleaning the device, disconnect it from the USB connection. If a hard drive is
installed in the enclosure, wait at least 30 seconds until the magnetic disks in the hard
drive have come to a complete stop.
Naturally, this is not required when using an SSD, since an SSD does not
contain any sensitive mechanical parts.
Use a clean, dry, soft cloth to clean the product. Do not use aggressive cleaning
agents, as these can cause discolouration.
To prevent scratch marks, do not press too strongly on the surface when cleaning.
Dust can easily be removed using a clean, long-haired brush and a vacuum cleaner.
Tips & notes
a) USB
• USB3.0 devices are backwards compatible. This means that they will also function
on conventional USB2.0 or slower USB1.1 ports, though only at the maximum USB2.0
or USB1.1 speed.
However, because the HDD/SSD and the hard drive enclosure require a current of
more than 500 mA , operation on a USB2.0/1.1 port is normally not possible (a USB3.0
port can supply a current of 900 mA, which is sufficient for operation).
So-called Y cables are available as accessories. These use two USB ports
simultaneously to supply the power (500 mA + 500 mA). In this way, the en-
closure can also be used with USB2.0/1.1 ports.
If you use such a Y cable, it is imperative you make sure that you first con-
nect the cable to both USB ports of the computer or USB hub (with power
supply) and then, last of all, connect the cable to the hard drive enclosure.
• Ideally, with USB3.0 a data transfer rate of more than 100MByte/s is possible. How-
ever, this depends on the HDD/SSD in your computer, the HDD/SSD installed in
the hard drive enclosure and the USB3.0 controller used on the motherboard (or a
USB3.0 plug-in card) and the data to be copied (many small files or one large file).
• For USB3.0, the cables should be selected to be as short as possible to avoid a
reduction in the transfer speed.
• To connect the hard drive enclosure to a USB3.0 port on your computer, you must
use a USB3.0 cable (e.g., the one supplied).
• If the hard drive enclosure is to be connected via a USB hub, the latter must also
support the USB3.0 transfer mode in order to achieve maximum speed. Only use
USB3.0 hub with its own power supply (e.g., via a wall plug transformer).
b) General
• The LED on the hard drive enclosure lights up when power is supplied and it flashes
during read/write access.
• USB devices can be connected and disconnected during operation.
You should, however, take into account that data may be corrupted or the operating
system may crash if the connection cable is disconnected while data is being trans-
ferred or while files are opened by a program.
In Windows, a symbol is displayed in the menu bar when the hard drive/SSD (or
other USB devices) are connected and in use. Click this symbol to "separate" the
device, i.e. to terminate data transmission, so you can disconnect the connection
cable without risking the loss of data.
• If you have upgraded your computer to be able to use a USB3.0 plug-in card (e.g., if
your motherboard still is not equipped with a USB3.0 port), you must check whether
the plug-in card has its own power connection.
If such a power connection is available, the PC power supply has to be connected to
it. Otherwise, the USB3.0 port does not function properly or does not supply enough
power. A hard disk enclosure with a HDD/SSD installed cannot be operated with
such a port.
Disposal
The product must not be disposed of in household waste!
Please dispose of the product, when it is no longer of use, according to the
current statutory requirements.

Technical data

Connection .................................................. USB3.0 (compatible with USB2.0/1.1)
Input voltage/ current................................ 5 V/DC, max. 900 mA
Appropriate HDD/SSD ................................ SATA I, II or III, 6.35 cm/2.5"
Installation height of the HDD/SSD ......... 7 mm
Ambient conditions .................................... Temperature -10 °C to +50 °C, relative air hu-
Dimensions (L x W x H) ............................. 125 x 79 x 10.5 mm
Weight (without cable/hard drive) .......... 73 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2016 by Conrad Electronic SE.
midity 10% to 85%, non-condensing