Samsung 6 Serie Mode D'emploi page 27

Masquer les pouces Voir aussi pour 6 Serie:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 56
Network Setup
(Samsung Auto Configuration)
This function is available in APs (Access Points) that support
Samsung Auto Configuration. If there is no such AP, you can
connect through PBC (WPS) or manually.
This function is available when
Wireless Link) set to Off.
You can check for equipment that supports Samsung
Auto Configuration on www.samsung.com.
How to set up using Samsung Auto Configuration
1. Place the AP and TV next to each other and turn them on.
Because the booting times of applications differ,
you may have to wait for approximately 2 minutes.
If the LAN cable connected the WAN port of AP
during Samsung Auto Configuration, you are able
to complete until Internet connection test. If you
do not connect, Samsung Auto configuration will
check only
2. After 2 minutes, connect the Samsung Wireless LAN
Adaptor to the TV. When the Samsung Wireless LAN
Adaptor is established, the pop-up window appears.
3. As soon as a connection is established, place the AP in
parallel with the Samsung Wireless LAN Adaptor giving a
gap no larger than 25cm.
4. Wait until the connection is automatically established.
If the connection fails, reset the AP and then try
again.
If Samsung Auto Configuration does not connect
your TV to your AP, a pop-up window appears
on the screen notifying you of the failure. Reset
the AP, and then try again. If the connection fails
again, choose one of the other connection setup
methods, PBC (WPS), auto, or manual.
5. After the connection is established, locate the sharer at
the desired location.
If the AP settings have been changed or it is the
first time you use the new AP after purchase, you
need to set up again beginning from Step 1.
Network Setup (PBC (WPS))
How to set up using PBC (WPS)
If your router has a PBC (WPS) button, follow these steps:
1. Connect your TV to your LAN as described in the
SWL(Samsung
2. Turn on your TV, press the
3. Use the ▲ or ▼ button to select Network in the Setup
4. On the Network screen, select Network Type.
5. Set Network Type to Wireless.
6. Select Network Setup. The Network Setup screen
7. Press the Red button on your remote.
8. Press the PBC (WPS) button on your router within 2 minutes.
9. After the network connection is set up, press the
Network Setup (Auto)
Most wireless networks have an optional security system
that requires devices that access the network to transmit
an encrypted security code called an Access or Security
Key. The Security Key is based on a Pass Phrase, typically
a word or a series of letters and numbers of a specified
length you were asked to enter when you set up security for
your wireless network. If you use this method of setting up
the network connection, and have a Security Key for your
wireless network, you will have to enter the Pass Phrase
during the setup process.
How to set up automatically
To set up the wireless connection automatically, follow these
steps:
1. Follow Steps 1 through 6 in the "How to set up PBC
2. Press the ▼ button to select Internet Protocol Setup,
previous section.
MENU
remote, use the ▲ or ▼ button to select Setup, and
then press the ENTERE button.
menu, and then press the ENTERE button.
appears.
Network Setup
Select a network
: Not Selected
Internet Protocol Setup
: Auto
IP Address
:
Subnet Mask
:
Gateway
:
DNS
:
Auto
DNS Server
:
U Move E Enter R return
Your TV player automatically acquires all the network setting
values it needs and connects to your network.
button to exit the Network Setup screen.
RETURN
(WPS)" above.
and then press the ENTERE button. Press the ▲ or
▼ button to select Auto, and then press the ENTERE
button.
button on your
27
English

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Le32c670Le37c670Le40c670Le46c670Le55c670

Table des Matières