Speaker Combinations - Pioneer ElitE SC-LX801 Mode D'emploi

> Before start > Hookup

Speaker combinations

In any of the combinations, up to two powered subwoofers can be connected.
Speaker
FRONT CENTER
Channels
2.1 ch
3.1 ch
4.1 ch
5.1 ch
6.1 ch
7.1 ch
2.1.2 ch
3.1.2 ch
4.1.2 ch
5.1.2 ch
6.1.2 ch
7.1.2 ch
4.1.4 ch
5.1.4 ch
6.1.4 ch
7.1.4 ch
Points to note with speaker combinations
＊ 1: It is not possible to use Speaker B, Bi-AMP, and ZONE speakers at the same time. However, with 2.1
ch to 7.1 ch, it is possible to use Bi-AMP (FRONT) and ZONE 2 speakers at the same time.
＊ 2: You can also use Bi-Amping connections with Speakers B.
＊ 3: If you have not connected ZONE 3 speakers in another room but have only connected ZONE 2
speakers, connect the ZONE 2 speakers to the HEIGHT 1 jacks. However, if you want to use at the
same time as Bi-AMP (FRONT), connect the ZONE 2 speakers to the HEIGHT 2 jacks.
＊ 4: If front speakers are to be Bi-Amping connected, height speakers need to be connected to the
HEIGHT 2 jacks.
＊ 5: ZONE 2 speakers need to be connected to the HEIGHT 1 jack, ZONE 3 speakers need to be
connected to the SURROUND BACK jacks, and height speakers need to be connected to the
HEIGHT 2 jacks.
＊ 6: This unit consists of a 9 ch amplifier, so when using a Bi-Amping connection for the front speakers,
use an RCA cable to connect the power amplifier to the PRE OUT HEIGHT 2 jacks, then connect the
> Setup > Playback
SURROUND
SURROUND HEIGHT 1
BACK
＊ 7
＊ 7
> Part Names
SP B
＊ 1
HEIGHT 2
(Speaker B)
＊ 2
＊ 2
＊ 2
＊ 2
＊ 2
＊ 2
＊ 4
＊ 4
＊ 4
＊ 4
＊ 6
＊ 6
height speakers to the power amplifier.
＊ 7: This unit consists of a 9 ch amplifier, so with this combination use an RCA cable to connect the power
amplifier to the PRE OUT SURR BACK jacks, then connect the surround back speakers to the power
amplifier.
HEIGHT 1/HEIGHT 2
When connecting 2 sets of height speakers, the height speaker combinations you can choose are as follows.
– Height 1 Speaker: Top Middle, Height 2 Speaker: Rear High
– Height 1 Speaker: Front High, Height 2 Speaker: One of Rear High/Top Middle/Top Rear/Dolby Enabled
Speaker (Surround)/Dolby Enabled Speaker (Surround Back)
– Height 1 Speaker: Top Front or Dolby Enabled Speaker (Front), Height 2 Speaker: One of Rear High/Top
Rear/Dolby Enabled Speaker (Surround)/Dolby Enabled Speaker (Surround Back)
When connecting only one set of height speakers, select one type of height speakers from the types
available.
ZONE 2 ZONE 3
＊ 1
Bi-AMP ＊ 1
( P19) (

FRONT
FRONT,
FRONT/CENTER
FRONT,
FRONT/SURROUND
FRONT,
FRONT/CENTER,
FRONT/SURROUND
＊ 3
FRONT
＊ 3
FRONT
FRONT
FRONT
FRONT
FRONT
FRONT
FRONT
＊ 1
En
P20)

＊ 5
＊ 5
＊ 5
＊ 5
9