Overlay Buttons; Using An External Timer; Troubleshooting - Norsup CYCLONE Serie Notice Originale

ROBOTIC POOL CLEANER TYPE CYCLONE

8.2. OVERLAY BUTTONS

MODEL
14 WWW.NORSUP.EU
Alterations which serve the technological progress as well as errors excepted!
ROBOTIC POOL CLEANER TYPE CYCLONE

8.3. USING AN EXTERNAL TIMER

(Optional, should be purchased separately)
An external timer can be used to automatically
activate the Cleaner on pre-set time. The external
timer should be connected between the wall socket
and the Power and Control unit
1. Unit
2. Cable
3. Power supply
4. Power supply plug
5. External timer (purchased separately)
6. Outlet

9. TROUBLESHOOTING

CLEANER DOES NOT TURN ON.
There is no electricity in the wall socket.
1. Disconnect cleaner from the power and control
unit.
2. Disconnect power supply from the wall socket,
wait 30 seconds and reconnect.
3. Turn power ON. If not activated, connect the unit
to a different wall socket.
Floating cable not connected properly to the power
and control unit.
Reconnect the floating cable to the power and
control unit.
Obstacle in the drive system of the cleaner unit.
1. Turn the cleaner unit carefully to view the underside.
2. Rotate the tracks and scrubbing brushes by hand.
It should rotate but it should not rotate freely.
3. Clean and remove obstacles and debris if necessary.
Propeller is seized due to accumulation of hair.
Check if the propeller is broken or needs to be
cleaned (see "Checking Water Outlet Propeller").
CLEANER MOVES BUT DOES NOT PUMP WATER.
Filters are dirty.
1. Remove the filters
2. Run the robotic cleaner in the pool without the
filters. If working properly, clean the filters well or
replace the filters.
Propeller is broken or seized due to accumulation
of hair.
Check if the propeller is broken or needs cleaning
(see "Checking Water Outlet Propeller").
Alterations which serve the technological progress as well as errors excepted!
CLEANER PUMPS WATER BUT DOES NOT MOVE.
Obstacle in the drive system of the cleaner unit.
1. Turn the cleaner unit carefully to view the underside.
2. Rotate the tracks and scrubbing brushes by hand.
It should rotate but it should not rotate freely.
3. Clean and remove obstacles and debris if
necessary.
CLEANER STARTS AND SHUTS OFF AFTER A SHORT
TIME.
Filters are dirty.
1. Remove the filters.
2. Run the robotic cleaner without the filters. If
working properly, clean the filters well or replace
the filters.
Propeller is broken or seized due to accumulation
of hair.
1. Remove the top screws on the top outlet.
2. Check if the propeller is broken or needs to be
cleaned.
Obstacle in the drive system of the cleaner unit.
1. Turn the cleaner unit carefully to view the underside.
2. Rotate the tracks and scrubbing brushes by hand.
It should rotate but it should not rotate freely.
3. Clean and remove obstacles and debris if necessary.
CLEANER DOES NOT PICK UP DIRT.
Filters are dirty or have holes.
Clean as needed and verify that there no holes in the
filters.
Propeller is broken or seized due to accumulation
of hair.
Check if the propeller is broken or needs cleaning
(see "Checking Water Outlet Propeller").
The suction inlet is not close enough to the pool
floor.
Move the suction inlet OUT (see "Adjusting Suction
Height").
DIRT COMES OUT OF THE CLEANER WHEN
REMOVING IT FROM POOL.
Filter shutter is broken or missing.
Open the filters and verify that the filter shutter is
not broken and functions properly (see "Cleaning
Filters")
Holes in the filters.
Open the filters and verify that there are no holes in
the filter screens (see "Cleaning Filters")
Bottom lid is not properly closed.
Make sure that the bottom lid is properly closed.
ORIGINAL MANUAL NORSUP
EN
DE
FR
15